Search results

The amount of data for the cooling systems is significant, although an emphasis was placed on monitoring corrosion rates.
This corrosion project developed extensive corrosion data on cooling towers.
Data and graphs to record system performance were stored in the system's controller memory, which supports approximately 40 days of data storage before overwriting previous data.
In addition to downloading these data monthly, wet chemistry test data, corrosion coupons, and measured corrosion information were developed and later transferred to an online reporting site.
Communication capabilities provide the opportunity to remotely monitor system performance, gather system data, and adjust operating parameters.

The entire router is a modular structure: control layer and data layer [8-9].
StrongArm in IXP2400 is responsible for control plane. 8 micro engines are responsible for the handling of data transmitted layer.
QoS system location in router QoS system is divided into two levels: control level and and data transmitted level.
Data transmitted level achieves in the network processing card.
If AVG< MINth, the new arrived data packet will be add to the queue, and the packet discard probability p = 0.

Each IDS client can monitor and capture the data packet passing through the neighbor nodes.
This algorithm will firstly find the suspected nodes in the list through checking the data consistency.
Wormhole attack can destroy the data packet of the routing and network of the WSN, which will lead to the reduction of location accuracy and communication quality of WSN.
(3) Resource exhaustion attack means that there will be conflicts between the data packets the attackers send constantly to the network and the data packets sent by the normal nodes.
The acquiescent defense mechanism will allow the sending nodes to send the data packet again.

It is that the amount of COO groups calculated from the IR and SEM-EDX data increases from 1.463 to 5.307 mmol g-1 with increasing oxidation time from 6 to 48 h.
These results also support the data obtained from FT-IR spectroscopy.
The amount of nitrogen adsorbed on the treated material decreases with increasing concentration of AP which reveals the reduction in the pore volume after the treatment.
The large reduction in the surface area and specific pore volume of the CKT-3 after AP treatment could be attributed to a partial collapse of the whole mesoscopic structure as powder XRD pattern of all the materials shows only a (100) reflection without any higher order peaks.

Some studies indicate significant reductions in surface temperatures could be achieved by spray cooling at low system pressures.
Relevant data shown in Tab. 1 indicate the disproportion between the enhancement of heat flux and heat transfer area.
Heat transfer enhancement on different structured surfaces (data from Wang et al.[4]) Structured surface Fin height (mm) Area enhancement (%) Heat flux enhancement at different volume fluxes (%) 0.044 (m3/m2s) 0.049 (m3/m2s) 0.053 (m3/m2s) Surface 1 0.1 38 39.0 39.5 41.0 Surface 2 0.2 76 53.0 67.0 72.0 Surface 3 0.4 152 31.6 22.0 18.0 In the study of Bostanci et al. [5], the enhancement of heat transfer was attributed to a stronger contribution of phase change mechanisms besides the increase in surface area.
But the scale of cooling capacity enhancement is always smaller than the growth of flow rate resulting in the reduction of spray cooling efficiency.

By means of the collected data, analytical models and two nomograms able to calculate the expected superficial residual stress value, once defined the experimental parameters, were defined.
The main advantage of the first strategy consists of the reduction in the computational time required to perform a simulation.
The use of two different solvers, as here proposed, can furnish a strong reduction of this computational time.
Outeiro for its support in providing the experimental data reported in this work.

A further reduction to the desired temperature of 760°C not only increases the stress unacceptably higher, but the material no longer strain hardens, as evidenced by the negative slope of the curve.
NKK released data for incorporation into Mil Handbook 5 specifying the same mechanical properties as Ti-6Al-4V.
In fact NKK data shows that it is superior to Ti-6Al4V up to about 400°C, the usual upper limit for Ti-6Al-4V. 0 20 40 60 80 100 120 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 True strain True stress MPa 760C 815C 900C 0 10 20 30 40 50 60 70 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 True strain True stress MPa 700C 760C Ti-64 at 900C Figure 1 Ti-6Al-4V alloy at 3x10 -4 strain rate Target Figure 2 SP700 at 3x10 -4 strain rate Figure 3 Micrograph of SP700 surface (with indenter) Figure 4 SP700 Microhardness One desirable attribute of SP700 is the resistance to alpha case formation at 760°C.
Initial trials on production part dies, figure 14, have shown that the new material can be substituted for regular Ti-6Al-4V with no change in the forming parameters except for the reduction in temperature setting of the press.

This paper discusses (i) the Nigerian Oilpalm resource in view of the currently projected one million-hectare plantation establishment between 2003 and 2007, (ii) available National milling facility and (iii) additional milling capacity requirement of the indigenously produced Digester Screw Press (DSP) oil palm fruit processing technology with a view to projecting its potential impact on poverty reduction, wealth creation and employment generation.
Operation data of DSP and other locally available palm oil extraction tools [3] DSP Digester + Hydraulic press Wet digester Digester + curb press Traditional pounding Efficiency (%) 85 70-90 75 65 50 Capacity (tonnes/hour ) 1.5 0.25 0.3 0.2 0.15 Daily FFB used (tonnes) 12 2 2.4 1.6 1.2 Labor (manday) 2 5 4 6 8 Over a period of 15 years the invention of this rugged machine has revolutionized the Nigerian smallscale oilpalm fruit processing industry.
Operation data of the DSP and other locally available palm oil extraction tools are shown in table 4 above.
Chan-Kang: Road Development, Economic Growth, and Poverty Reduction in China Research Report 138 International Food Policy Research Institute Washington, DC (2005).

This type of defect tends to develop in thermal reduction and eletro-reduction environments, both of which exist in SPS [12].
Table 1 E, H and G of sintered HA pellets MS NR-L NR-H NS E [GPa] * 107 ± 2 114 ± 3 123 ± 5 130 ± 5 H [GPa] * 5.9 ± 0.2 6.8 ± 0.3 6.3 ± 0.5 7.2 ± 0.6 G [nm] 411.3 362.9 774.2 N.A. * Data presented as the mean ± the S.D. with sample size n = 20.
The presence of CaO phase was confirmed by XRD (data not shown).

Framework Convention on Climate Change held in Kyoto in 1997, the Architectural Institute of Japan (AIJ) stated in 1999 that new building construction projects should aim at a 30 % reduction in life cycle carbon dioxide (LCCO2) emissions and a three-fold increase in building service life [3].
Along with such fabrication data, their positional information and product inspection data are registered in the database.
The grade degradation of structural members is Ri5(S5) (JIS K 5600-8), but these reductions of thickness of reusable members obtained are not occurred.