Search results

For the motion buffer, two-stage buffer is employed: the first stage is used to store the data that is being executed; the second is used to store the data that is being received.
Second, if the data enters the FPGA, the motion controller checks its state.
Because the motion controller blocks the data while the motor is running.
If the motion controller’s state is idle, the motion controller uses the data for operation.
Next, the motion controller’s mode enters a running state and transfers motor speed data via the state buffer to the host.

Some of the data are reported in Fig. 1.
Some normalized isothermal absorption data sets obtained with sample V2 are reported as a function of time in Fig. 2.
Dotted lines are fits to the experimental data according to Eq. (2).
According to the data these stresses would facilitate the formation of the martensite on cooling and oppose to their disappearance on heating.
At low H contents absorption and Snoek relaxation data allow the determination of the diffusion coefficient of H over a wide temperature range.

The sensing system of TEFPI optical fiber sensor and the data reduction principle for the detection of compliance changes are presented.
Fig. 4 shows the relationship between strain by TEFPI optical fiber sensor and load data.
The strain data was calculated by counting of the interferometric fringes shown in Fig. 3.
Strain data of TEFPI sensor located at the center point.
Fig. 6 Crack length vs. strain data of TEFPI sensor located at the 15 mm ahead of crack.

Data are given on the rock mass removal for various filling methods, as well as for the resistance values for the piling wall movement and the energy capacity of the hopper filling process for operating with sandy loam, loam, clay, and limestone crushed stone.
The use of an elongated hopper is rational from the economic point of view: an increase in the volume of the hopper leads to a reduction in the number of movements of the scraper for the transfer of rock mass.
During the experiments, there is inevitable experimental data dispersion as a result of the occurrence of systematic and random errors.
For crushed stone, the resistance reduction is 3…5% and is primarily due to a change of the inclination angle of the hopper bottom to the horizon.
Vedenyapin, General procedure for experimental research and processing of experimental data, Kolos, Moscow, Russia, 1973. https://books.google.com.ua/books?

It can be reason of difference between the CFD results and the experimental data.
The comparison of two results of numerical simulations with the experimental data [8] is shown.
We evaluated the value of the kinetic energy loss coefficient ζ = 1-M2*2M2is*2 (where the Mach number M2is*2 is related to the inlet free-stream total pressure) applying the data reduction method on data from traversing line.
The start of transition as well as the transition length are even captured in good agreement with the ERCOFTAC data.
Numerical calculation of the VKI test case for all used methods gives results, which are similar to experimental data.

The 80 raw variables, selected depending on the data availability and the scale of uniformity Istat, Istituto Tagliacarne, Agenzia del Territorio, Il Consulente Immobiliare, Miur, Espon, Corine Land Cover, ecc. are just some of the several data sources introduced in the evaluation model.
The data selected had to satisfy criteria such as public diffusion, geographical scale (NUTs-3 level: “provinces”) and time series uniformity (from 1995 or 2000)
even if three real estate residential variables (here represented by means of real data - see fig. 2) present remarkable ratings.
The variables are: price levels of new stock The data used in the macro RCAU dataset refers to the “Il Consulente Immobilare”, a periodical magazine published by the main economical editor “Il Sole24Ore”.
The demographic analysis, based on the differences between the last two Italian population census data (Istat, 2001; Istat 2011), evidences that the most relevant demographic increases have been registered from 2001 to 2011 Fondazione ISMU elaborations on ISTAT data (Istat- Italian National Institute of Statistics, 2001 census data; Istat- Italian National Institute of Statistics, 2011 census data)

Or fitting empirical data to a non-linear model in its original form.
Firstly, the experimental data are entered into the sheet with the independent variable (t) data column preceding the dependent variable (q) data column.
Then, the data are plotted to obtain the graph of q against t.
Next, an error function model is added to calculate and evaluate the deviation of the experimental data from the model data.
In isotherm study, a model is first proposed, the experimental data are processed according to proposed model and the isotherm data are then plotted.

In the past, noise reduction algorithms [3] [4] based on wavelet or wavelet packet were developed.
In the process of data acquisition, we select a single microphone which is connected to a laptop as the audio input device.

According to the actual data of the rolling conditions, the shaping process of 52B from flat wires to shaped wires was studied in this article through finite element analysis by using the DEFORM-3D.
In Fig.3, the change of the grid on the cross-section of the rolledpiece is illustrated schematically, which shows the size of the rolledpiece section varying greatly, namely the deformation of the tooth is larger than that of the base due to much rolling reduction on the tooth.

It results in further deterioration of the material’s quality Wavelet Denoise The actual measured signal contains noise, it tends to obscure the useful information, so it is necessary to denoise the signal .Because the wavelet analysis is easy to operate and has good noise reduction effect, it is widely used.
The primitive figure of rolling force was drawn according to the measured rolling force data, as shown in Fig.3.