Search results

(2) Where Mg-Si-O is mainly accumulated onto the surface of oxidization layer, it has large and hard grain, thus the membrane surface is relatively coarse.
However, due to limited number of severe sparking, the discharge is not so even, thus the roughness on surface of membrane is relatively high.

In this notation, A represents a mono-, bi- or trivalent ion, B denotes a tetra-, penta- or hexavalent ion, and m is the number of BO6 octahedral in each pseudo-perovskite block (m = 1–5) [7].
The grain growth in the samples was found to be strongly anisotropic and plate-like, which is characteristic of BLSF ceramics [13,14].

To solve this problem, the surface modeling technology of CAD/CAM has been used and solved it. 2.1 Theory of modeling parts with freeform surfaces （1） The expression of the freeform curve A freeform curve is a curve with no specified shape; it can’t be described as a straight line, a circular arc or a second conical section, but can be only described as a certain numbers of discrete points. [2]In practical use, the curve is always built by mathematical algorithm since the particle array, the trend of the array, and the join condition have been given, it gets through or close to the specified mass points.
It can be built by sweeping, also can be made of curve grid or the curve, even by creating the straight grain surfaces. [7-9]Usually on the basis of the appearance requirement, we can establish the boundary curves or build the curves according to the sample measurement data points for the surface, then establish the surface by the surface built methods of UG.

If the interface adhesion tends to an ameliorative state, the number and the intensity of the interface slip would be reduced; and the same reason would make the interface relaxation effects occur in higher Fig.3 Temperature dependence of Q -1 in the EB-PVD NiCrAlY coated samples and the substrate.
Different to usual interface relaxation, such as the grain boundary relaxation, no obvious modulus soften effects [13] appears in modulus-temperature curve.

The size number of SiC grains was 180#, 240#, 320# and 500#, respectively.

Step4: Return to Step3, until the number of elements in S reaches k. 5 fixations are extracted using conspicuous edge positioning method as shown in Fig4.
Fast, automatic and fine-grained tampered JPEG image detection via DCT coefficient analysis[J].

Introduction Porous ceramics, sintered at high temperatures with a large number of internal or closed pores connected to each other, rely on the pore structure and the material itself to achieve the desired functionality.
The carbon fibers mentioned in this study are high-strength, with low graphitization degree and preparation temperature, and in the edge of the grain boundaries there are a lot of active points which are prone to reactions and cause the mechanical properties of fiber to attenuate seriously.

Optional iron mainly in the form of magnetic iron content of 6.32%, its share of 36.94%, followed by hematite, limonite, content was 2.87%, and its share of 16.77%; iron silicate minerals content of 6.73%, 39.33% of the total iron content; while a small amount of iron to form iron carbonate and iron sulfide present, the amount of 0.26%, 1.52% of the total iron content. 1.2 Sample size analysis Table 3 Iron distribution in each grain Sizefraction （mm） Productivity（%） Accumulation of positive Productivity（%） Accumulation of negative Productivity （%） Grade （Fe%） Distribution rate（Fe%） +0.5 2.59 2.59 100.00 9.21 1.36 -0.5+0.3 15.05 17.64 97.41 9.37 8.04 -0.3+0.165 13.47 31.11 82.36 10.25 7.88 -0.165+0.074 26.38 57.49 68.89 15.20 22.87 -0.074+0.047 8.74 66.23 42.51 22.09 11.01 -0.047 33.77 100.00 33.77 25.35 48.84 Total 100.00 17.53 100.00 Table 3 shows the results of particle size sieve analysis, processing recycled objects mainly enriched in iron -0.047mm level, up 25.35 percent
Research shows that lost to tailings iron minerals are mainly of two parts, one part is not a large number of coarse particles monomer dissociation, and the other part is fine iron particles over crushed minerals produced. 2 Experiments Through the properties of iron ore tailings in Yunnan shows: coarser ore, mineral composition is relatively complex, as many as a dozen have been identified mineral species, useful minerals are mainly magnetite (partial oxidation of martite ), hematite, limonite.

The influence mechanisms of ultrasonic vibration to hot-dip aluminizing include cavitation effect and current effect which can lead to minuteness of crystal grain, gas elimination and homogenizing of organization.
(Subject number: 2007BSB01502) References [1] D.H.

Legend: [1] TVA gun – cathode [2] Crucible [3] Material to be evaporated (C, Mg grains) [4] Substrates (Si and glass) [5] Thickness monitor Fig. 1 The schematic view of the experimental set-up The main experimental parameters involved in this study are: If- the current intensity of the heating filament; Ua- the applied voltage; Ia- the arc’s current intensity; d- the distance between samples and the point of the ignition of the discharge; p-the pressure; tdep- the deposition time; φ- the cathode-anode relative position between a perpendicular line on the crucible centre and the electron gun axis.
Acknowledgment This work was supported by a grant of the Romanian National Authority for Scientific Research, CNDI–UEFISCDI, project number 160/2012, PN-II-PT-PCCA-2011-3.2-1453.