Search results

Materials and methods Materials PVA(DP: 2200) were purchased from Shanxi Sanwei Group. 50% glutaraldehyde, ether and Span-80 were provided by Tianda Chemical Reagent Factory(Tianjin,Chian).
Journal of Biotechnology.
Materials Science and Engineering A.
Journal of Magnetism and Magnetic Materials.
Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms.

The FAO/S8010 silica particles slurry (Tianjin Jingling Electronic Materials Technology Co., Ltd.) with density of 1.1g/cm3, concentration of 35wt%, mean diameter of 30~40 nm and pH 11.0~12.0, was used as basic polishing slurry.
Xu and et al: Chinese Journal of Mechanical Engineering Vol.19(20) (2008), pp:2407-2411
Lu: Science and Technology of Particle Dispersion, Chemical Industry Press, China 2005
Liu and et al: The Chinese Journal of Process Engineering, Vol.4 (6) (2004), pp: 513-518
Yuan and et al: Chemical Journal of Chinese Universities, Vol.26 (11) (2005), pp:1998-2001.

Meng: Journal of manufacturing Science and Engineering Vol.118 (1996), p. 461 [14] E.
Huang: Journal of manufacturing Science and Engineering Vol.128 (2006), p.249 [16] S.D.
Altintas: Journal of Manufacturing Science and Engineering Vol.130 (2008), p. 051004-1-12 [17] W.B.
Yip-Hoi: Journal of Manufacturing Science and Engineering Vol.130 (2008), p.051011-1-12 [18] B.K.
Altintas: Journal of Manufacturing Science and Engineering, Vol.130 (2008), p.51 [20] S.W.

Acknowledgements This work was financially supported by the National Natural Science Foundation of China (51368019), Science and Technology Program of Science and Technology Agency of Jiangxi province (20122BBG70186), Science and Technology Program of Education Department of Jiangxi province (GJJ13327), and Jiangxi Higher Education Innovation Program (JXJG-14-5-31).
Journal of East China Jiaotong University, Vol. 17-2(2000), p.40～45.
Journal of East China Geological institute, Vol. 26-3(2003), p.271～273.
Journal of Engineering Mechanics, Vol. 24-supp.1 (2007), p.66~69.
Advanced Materials Research, Vols. 655-657(2013), pp:1889-1892. (2013) Trans Tech Publications, Switzerland. doi: 10.4028/www.scientific.net/AMR.655-657.1889

Hubei Agricultural Sciences, 2010, 46 (4): 464-465
Journal of materials engineering, 2011, 23 (4): 158-161
Peanut journal, 2011, 36 (4): 18-21
Journal of crops, 2011, 34 (6): 1069-1073
Journal of Zhejiang University using: Engineering Science, 2010, 40 (1), 53-57.

Liu, Journal of Materials Chemistry, 20 (2010) 5993-6008
Dickey, Journal of Materials Research, 16 (2001) 3331-3334
Grimes, Journal of Materials Chemistry, 21 (2011) 13429-13433
Dékány, Chemistry of Materials, 19 (2007) 4811-4819
Navarrete, Journal of Sol-Gel Science and Technology, 37 (2006) 165-168

Influence of Parameters on Fabricating TiO2 Nanotube by a Hydrothrmal Method Zheng Fangfang, Zhang Wenli1,a ,Zeng Xiongfeng 1College of Materials Science and Engineering, Hebei United University, Tangshan, Hebei Province, CHINA azhwl@heuu.edu Keywords: titania Nanotube; Hydrothermal Temperature; Hydrothermal Time; Washing Conditions Abstract.
TiO2 nanotube was synthesized successfully with different parameters via hydrothermal process, using nano-powder TiO2 and concentrated NaOH solution as raw materials.
Novel nano-structured materials: synthesis and application, J.
Chinese Journal of Catalysis. 30 (2009) 37-42
Journal of Materials Chemistry. 17 (2007) 2095-2100.

Introduction Recently, a lot of researches are focused on creating new combinations of materials.
In these group of materials are ceramic matrix composites with the metal addition [1,2].
Pecharroman, The challenge of ceramic/metal microcomposites and nanocomposites, Progress in Materials Science 52 (2007) 1017-1090 [2]K.
Szafran, Ceramic-metal composites with an interpenetrating network, Materials Chemistry and Physics 81 (2003) 329-332 [3]K.
Tanimoto, Mechanical performance of 3Y-TZP/Ni composites: bending, and uniaxial fatigue tests, Journal of Materials Research 17 (2002) 1592-1600 [9] A.

Yu1,b* 1AECC Key Laboratory of Aeronautical Materials Testing and Evaluation, Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Key Laboratory of Aeronautical Materials Testing and Evaluation, Beijing Institute of Aeronautical Materials, Beijing 100095, China axjxxrd@qq.com, byhcyu@126.com Keywords: Additive manufacturing (AM), Fatigue, Building orientation, Defect Abstract: Addictive manufacturing (AM) allows for the layer-by-layer fabrication of components via sequential material deposition and it is of immediate interest in many applications, in particularly aviation field.
Comprehensive Materials Processing, 2014, 10: 93-134
Materials Science & Engineering A, 2014, 598: 327-337
Materials Today: Proceedings, 2016, 3: 921 -924
Materials Science & Engineering A. 2016, 652: 105-119.

Fomina, Nonlinear dynamic analysis of a reinforced concrete frame by the boundary element method, Materials Science Forum, 968 MSF (2019) 383-395
Surianinov, Experimental studies of reinforced concrete and fiber-reinforced concrete beams with short-term and long-term loads, Materials Science Forum, 968 MSF (2019) 227-233
Tkach, Resource-Saving technology of manufacturing of semifinished products from intermetallic γ-TiAl alloys intended for aviation engineering, Materials Science, 55(6) (2020) 908-914
Yeremenko, Mathematical modelling of professional risk at Ukrainian metallurgical industry enterprise, Journal of Achievements in Materials and Manufacturing Engineering, 1(108) 35–41 (2021)
Belokon, Investigation of corrosion and oxidation of γ-TiAl alloys obtained in self propagating high temperature synthesis, Materials Science and Technology Conference and Exhibition, 2 (2015) 1249-1255