Search results

Energy consumption data is mainly from China energy statistical yearbook.
Tab. 1 Average coefficient of carbon emissions in northeast China Provinces Liaoning Jilin Heilongjiang The average coefficient of carbon emissions 0.7275 0.7297 0.6928 Higher than the national average/% -1.6759 -1.3786 -6.3657 Note: the national average coefficient is 0.7399, negative represents lower than the national level, The data comes from the China energy statistical yearbook from 1997 to 2011.
From these data we can infer population size will play a minor role in increasing the carbon emissions of northeast China.
This implies that energy efficiency is the most important factor in slowing industrial carbon emissions and the most feasible key factor in achieving the goal of carbon reduction.

With the further reduction of the axial height (z/T), w attenuates quickly along the axial, and the position of maximum axial velocity moves to the direction of 2r/D increasing.
Through the analysis of the experimental data, the boundary linear expansion equation of upward axial flow can be expressed as Eq. (1).
The experimental data shows that fluctuating velocity values of the impeller discharge flow are significantly higher than the main loop region, turbulence intensity of impeller zone and impeller discharge flow region is bigger.
As there are only tangential and axial velocity components in the data of the experiment,so we assume local isotropy,than Eq. (2)can be simplifiedasEq. (3).

At small set rolling reductions, the observed pressures are generally between 85MPa and 260MPa.
Nominal stress-strain data for aluminium alloys Table 3.
Summary On the basis of the compression data analysis the quantitative relation of the material’s yield stress in function of the kind and content of alloying elements was demonstrated.
Similar conclusions can be reached by analyzing the data of changes in the hardness during cold rolling and the values of average pressures, obtained in the process of cold rolling.

Literature data indicates that, depending on seasonality, the content of phlorotanins in F. 
Vesiculosus, w = 60 % Vacuumation to 50 mbar 5 min exposure at 50 mbar Filling of reactor with CO2 to 3 bar 5 min exposure at the selected temperature Heat to 100 °C Reduction of excess pressure Treated F.
Retention time, min [M-H]- (m/z) Identified compounds 0.49 497 Fucodiphlorethol (a phlorotannin tetramer) 0.32 511 Eckol tetramer with one additional hydroxyl group 0.40 1055 Eckol octamer with four additional hydroxyl groups 0.45 869 Fucophlorethol with seven phloroglucinol units 0.32 621 Fucotriphlorethol Based on the literature data about high antioxidant and antibacterial activity of phlorotannins [5], we evaluated the antibacterial activity of the extract (CEE).
The data on antibacterial activity allow us to recommend F. 

With the development of the miniaturization and weight reduction of sensor devices, the graphene, which is the most conductive material, has attracted widespread attention.
The strain measurement equipment is the TDS-530 static collection instrument, which is set to collect data per second.
The strain data is the average value of the real-time data corresponding to the two strain gauges on the specimen.

The selection of the mesomodel mechanical characteristics was based on data of the micro-level model.
The calculated curves and data, obtained in micro- and mesomodels, correlate well with each other.
Correct consideration of microdamages in the layers, which lead to a reduction in the structure's overall rigidity and to a redistribution of stresses in the layers, is a necessary stage in the calculation of the softening kinetics and in the prediction of complete destruction.

Based on meteorological observation data and environmental monitoring data of Changsha in the period from 1970 to 2012, this paper analyzes the distribution characteristics and import factors of the haze weather in Changsha.
During the period from 1970 to 1977, there were no haze days; during the period from 1978 to 1986, the haze days increased year by year, but the annual haze days were all below ten days; during the period from 1987 to 1999, the haze days continued to increase, and the averagely annual haze days were more than 30 days; in 2000, the haze days reduced sharply from 33.5 days/year in 1999 to 17 days/year, reducing by half, in this stage the economic development was stable, and the environmental protection measures were standardized and perfected gradually, being important factors of reduction of haze days; during the period from 2001 to 2012, the haze days increased sharply, in 2011 the haze days reached 129 days, in 2012 they were 97.5 days, and this situation has direct relationships with the rapid development of economy, the expansion of urban construction scale and the increase of motor vehicle population.

Selection of this method enabled to determine the impedance of the material – surface layer – solution interface with the use of approximation of impedance data by means of equivalent electric circuit model.
In every process of electrochemical corrosion, there are two processes that always occur on metal surface, i.e. oxidation (anodic processes) and reduction (cathodic processes) [12].

There is a large research potential in super-plastic forming; from the determination of optimal material data through process simulation to manufacturing of real parts and their characterization.
The reduction in the stretch at break can be explained by the flow behaviour of the material.

Related scholars utilize different data sources and seek ways to study them.
It used radar satellites and airborne synthetic aperture radar (SAR) image data,thematic mapper(TM) data, SPOT data and high resolution data of other sources and combined with the geographic information system (GIS) technology to carry out multi-level monitoring and detailed evaluation in serious disaster area.
Besides satellite data format and the standards of RS data processing and assessment are not unified.
The production and updating of high precise based data Flood disaster monitoring and evaluation is based on having the high accurate and real-time bottom data.
But the continuously updating of data and the improvement of technology still can't be guaranteed.