Search results

Introduction The same deformation texture can develop different annealing textures depending on stacking-fault energies of materials (Al stacking-fault energy (SFE): 166 mJ/m 2 [1], Cu SFE: 78 [1], Au SFE: 45 [1], Ag SFE: 22 [1], Cu-7.3% Al SFE: <20 [2]) [3].
Contour levels: 1, 1.5, 2, 3, 4, 5 [2].
ing at high temperatures as represented in Figs. 1 and 2.
References [1] L.E.
Forum Vol. 475-479 (2005), p. 1 [17] D.N.

In addition, high cycle vibration at the steam inlet leads to the initiation and propagation of cracks [1].
Fig. 1 showed the schematic configurations of hot gas casing.
The mechanical properties of test materials are shown in Table 1.
Table 1 Mechanical properties for testing materials B.M.
Conclusions (1) The damage mechanism for hot gas casing was investigated.

The mechanics experimental study of the artificially frozen soil in Cretaceous strata Hao Cui 1，a, Dong-Wei Li 2，b, Ren-He Wang2，c 1Beijing China Coal Mine Engineering Co.
Test requirements and test steps 1.
The trials conducted using strain-controlled loading strain rate of 1%.
The strain rate controlled loading ways of frozen soil instantaneous uniaxial compressive strength test: 1.
The typical stress-strain relationship of the permafrost in room temperature, -5 ℃, -10 ℃, -15 ℃ as shown in figure 1.

The absorption peaks at 424.36 cm-1 and 510.19 cm-1 are attributed to Zn-O stretching vibration as previously reported in literature [1, 11].
References [1] S.
Res. 4 (2013) 479–484
Sci. 13 (2019) 1– 22
Technol. 1 (2013) 118–120

Chernev 1,d, Evgeniy A. 
Table 1.
Fig. 1.
The broad peak at 225 cm-1 can be decomposited into two Gaussian peaks at 224.1±0.06 cm-1 and 232.7±0.34 cm-1.
Kawanami, Heteroepitaxial technologies of III-V on Si, Solar Energy&Solar Cells 66 (2001) 479-486

Table 1.
References [1] L.
Ge, Preparation and Characterization of Betulin Nanoparticles for Oral Hypoglycemic Drug by Antisolvent Precipitation, Drug Deliv. 21, 6 (2014) 467–479
Mater., (2022) 1-11
Mater. 850, 1 (2020) 3–8

Eq. (1) is a time-dependent partial differential equation, which can be solved by a finite difference scheme developed in Ref. [1].
The time step is set as 1.0s.
References [1] H.J.
Thomas, Modeling of harbor resonance in port of long beach, Civil Engineering in the Oceans VI (2006) 479-493
Mech. 114 (1988) 1-23

This technology is applied by a number of researchers for the deformation of casting Al and Al-Cu alloys, where the measurement results obtained prove that the initial grain size diameter of 470 µm is refined to 479-669 nm as a result of ‘A’ route equal channel angular pressing [2].
a) b) c) Figure 1 Interpretation of anisotropy in the field of vision [8] a) anisotropy ~1, b) anisotropy >1, c) anisotropy <1 On the basis of professional literature, the objective of the research work was to investigate aluminium alloy samples (AlCuSiMg) which had been powder metallurgically pressed and sintered, as well as those which had been precipitation hardened, and also samples with a material quality of (AlCuSiMg) which had been ECAP-ed after sintering in terms of mechanical properties and grain structure.
For a sintered sample this is 1 or a value close to 1 due to the initial equi-axial grain shape (the number of the horizontal and vertical sections is nearly identical).
Some of the sintered samples were precipitation hardened, while the rest was ‘A’ route equal channel angular pressed. 1.
References [1] Viswanathan, V., Laha, T., Balani, K., Agarwal, A., & Seal, S.

Multimaterial and Multiscale Rapid Prototyping of Patient-Specific Scaffold Aurora De Acutis 1,a*, Carmelo De Maria 1,2,b and Giovanni Vozzi 1,2,c 1Department of Ingegneria dell’Informazione, University of Pisa, Pisa, Italy 2Research Center E.Piaggio, University of Pisa, Pisa, Italy aaurora.deacutis@for.uni,it, bcarmelo.demaria@centropiaggio.unipi.it, cg.vozzi@ing.unipi.it Keywords: rapid prototyping, tissue engineering, scaffold, multi scale, multi material.
As show in Fig.1, this tool was a modified to allow the deposition of both separated material but also their combination.
Fig.1.
References [1] C.L.
Eur Spine. 17(2008), 467-479

The 5 mM NO3- nutrient solution contained 4 mM KNO3, 1 mM Ca(NO3)2, 3 mM CaCl2, 1 mM K2SO4, 1 mM MgSO4, 0.6 mM KH2PO4, respectively.
NRA in leaves increased with increasing NO3--N supply at both 0 and 1% NaCl (Fig. 3; Table 1).
Table 1.
References [1] R.
New Phytologist. 159: 479-486. (2003) [17] X.J.