Search results

Microstructure of the cooled samples consists of pearlite (the darkest phase), bainite (grey phase mainly near the borders of grains) and the bright ferrite.
Using this brand new technology, the ATOS Triple Scan produces a high accuracy and improved measurement of shiny surface, complete data on complex components with deep pockets or fine edges such as turbine blades, reducing the number of individual scans and resulting in a simple handling.
Acknowledgment The project has been supported by the Polish National Science Centre, Decision number: DEC-2011/03/D/ST8/04041 References [1] C.G.

Hardness increased with applying mechanical alloying and also with decreasing grain size.
Acknowlegment This study was supported by “The Scientific and Technological Research Council of Turkey (TÜBİTAK)” with the project number of 214M093.
,Zhnag, C., Wang, R., Peng, C., Qui, K., Feng, Y., “Preparation of Al–Si alloys by a rapidsolidification and powder metallurgyr oute”, Materials and Design, vol. 87, 996–1002, Publication number: 10.1016/j.matdes. 08.106 0264-1275, (2015)

The basic statistics for these datasets are presented in Table 1, where: "Number of Drugs" indicates the quantity of drugs in each dataset, "Number of Targets" represents the number of targets in each dataset, "Number of Interactions" signifies the count of DTIs in each dataset, "Interactions Proportion" denotes the ratio of drug-target pairs with interactions to the total number of drug-target pairs.
Part 1 represents the targets with the least number of interactions, Part 2 represents those with the second least number of interactions, and so forth.
This is because the number of negative samples for these targets far exceeds the number of positive samples, as illustrated in Fig.3.
Therefore, the number of neighbors can be set to either 5 or 7.
Fine-grained selective similarity integration for drug–target interaction prediction.

Organization of the Text This experiment designs 3 GFRP tube SRHC members in bending in total, and the outer diameter of the test sample is 200mm, and the effective span is 1200 mm, and the concretes strength is C70 and the reinforcing steel uses the I10 number I-steel.
Table 1 Parameters of tested and calculated results Test sample serial number Twist (Angle degree） Wall thickness Tested results Computed results Computed results/test results WGSC1 80 5 65.4 71.8 1.098 WGSC2 60 5 72.36 77.75 1.07 WGSC3 60 3 61.8 55.9 0.91 Manufacture of test sample 1) Keeping the GFRP tube’s and reinforcing steel’s length are the same, and reinforcing steel is welded into the 10mm thick terminal plate.
When it reaches its limit value, as to maintain the state of equilibrium, component's load unceasingly drops and the deformation rapidly increases, and the GFRP tube presents white grain along the fiber direction.

Nowadays, there are a number of hardware and software support products in the precision fruits, such as 3S (GPS, GIS and RS) technique applied in agriculture, spatial field data acquisition device and data processing software, agricultural machinery of intelligent variety operation, decision support system for field information management and crop product management and the technology and product of system integration.
ASA Special Publication Number 66, American Society of Agronomy, 2003, Madison, WI
Spatial variability in yields and profits within ten grain sorghum fields in South Texas.

If use the same number of measured value to do statistic analyze, large test specimens average ​​of measured values must be lower, less variability in the measured values is one of the main reasons caused by size effect[1].
Based on the definition of non-standard size in "common standards for mechanical testing of concrete" ,the set of number and content of test are according to the following table.
While changing the axial specimen size from 100×100×300mm to 150×150×300mm, though grain size of cerammisite is small, aggregate can be well wrapped by cement slurry.

Hence, a great number of development efforts are being made on material improvement and surface treatment technology for those parts.
It is well known that heat treatment or hot working of a plastically formed material can occasionally enhance surface hardening due to strain ageing and grain refinement.
The cycles of 107 were taken as limiting number for evaluation of fatigue properties.

Zhang [7] discussed the effects of positioning errors, the number of tooth, and the helix angle on the accuracy of the ground tooth flanks.
Because the grinding wheel is subject to wear, the grinding grains lose their cutting ability and the wheel have thus to be dressed again as long as every several gaps are ground.
Table 1 Parameters of gear and diamond roller Items Units Values (A) Gear data Normal module mn mm 14 Teeth number z - 76 Pressure angle αn degr. 20 Helix angle β degr. 15 R.H.

The iron ion (Fe3 +) in the BaM structure has an oxidation number +3 with an ionic radius of 0.065 nm, while Zn2+ has an oxidation number of +2 with an ionic radius of 0.074 nm.
The grain size obtained is quite large, because the given calcination temperature treatment is also high.

For the same road without paving the soil material, the numbers of above two kinds of cracks are 25 and 13 respectively.
From these numbers, it is deserved to believe that paving the soil material is effective to pretend the reflection cracks.
(iv) Setting up the isolated layer made by asphalt chips To alleviate the extension of the reflection cracks, another way is to pave a layer of big grain diameter asphalt chips or structural layer composed by the graded stone chips.