Search results

SPS, having a faster heating and cooling rate as compared with that of hot-pressing method, can prepare highly dense ceramic samples in a short time which can suppress the grain growth, and reduce the thermal conductivity.
All the κe values can be calculated by using the Wiedemann-Franz law expressed by κe=L0T/ρ, where L0 is the Lorentz number (here L0 = 2.443×10-8 WΩK-2 for free electron is adopted for the estimation).

Although most of the particles were spherical particles, some particles with irregular structure were obviously found, and agglomeration phenomenon happed in a small number of silicon particles.
Neophytides, Nikolaos Georgoulas, Electrochemical Impedance Spectroscopy study in micro-grain structured amorphous silicon anodes for lithium-ion batteries, Journal of Power Sources.331(2016), 285-292

Moreover, in general, it is accepted that a network component of specific heat, in a case of iso-structural compounds of lanthanides, this component is very close to itself and drops down with increase of an atomic number of the element i. e. from La to Gd [7].
In the presented results, commercial powders were applied, which are provided strictly to a plasma spraying process on ceramic layers by the APS method of precisely known chemical and phase compositions, size and shape of grains and its interior structure and surface morphology [21].

A large number of coating techniques are available such as pack cementation, chemical vapor deposition (CVD), thermal spray, plasma spraying, etc.Fused slurry or slurry-fusing is a solid-liquid reaction diffusion process, in which the coating is formed by the interaction of substrate and melt.
After analysis and discussion,it can be found that thecoating fabricated at 1450°Cshowed excellent structure compatible with high temperature oxidation resistance. 2) The surface of coating at 1450°Cis relatively smooth with few holes and cracks and uniform grain particles; the main phase of the surface is (Ti,Ta)Si that has better high temperature oxidation resistance;the cross-sectional structure of the coating is smooth and compact which can effectively prevent O2 from penetration. 3) Moreover,the cross-sectional morphology and composition of the specimen coated at 1450°C were discussed in details.The coating has a dense multilayer structure and three layers can be observed from coating to matrix: (Ti, Ta)Si2 TaSi2 Ta5Si3+ TaSi2. 4) At last, the isothermal oxidation behaviors of coatings in pure O2 atmosphere at 1500°C for 2h were investigated.

Five catalysts indicated as Co10/CeO2, Co10-Ni10/CeO2, Co10-Ni20/CeO2, Co10-Ni30/CeO2 and Co10-Ni40/CeO2 were prepared (the numbers in the catalyst mean the molar fraction in percentage).
Typically, about 200 mg catalyst with 60–80 mesh grain size diluted with quartz sand was loaded into the reactor to achieve a catalyst bed height of 5.0 mm.

Crushed gravel particles with the maximum grain size is not greater than 25mm, continuous gradation gradation to comply with the 5~20.
After adding NC-H, in the age of 3d Ca(OH)2 is significantly reduced, the volcano ash effect of NC-H significantly, the number of C-S-H increased, Ca(OH)2 crystals become small and irregular, make the structure compact.

What’s more, with more crosslinker, radicals would be wrapped by the polymer net, which can decrease the collision possibilities between radicals and increase the number of chains.
They are large specific surface area with a grain size shorter than 2um, allowance of water into the lattice layers causing swelling and the mutual repulsion by anions on its surface.

Therefore, many adsorbents can be used as effective alternatives [7].The materials are natural clays, alkaline earth, fine-grained and chemically formed by hydrated silicates of aluminum, iron and magnesium.
They consist of extremely small crystalline particles of a limited number of known as mineral clay, may also contain organic matter, soluble salts, quartz, pyrite, calcite, and other trace minerals amorphous minerals [8].

Results and Discussion 2.1 Organic matter composition analysis of produced water water quality of low permeability oilfield produced water is complex, mainly including the crude oil which has not been isolated from production, suspended solid (sediment organic matter, colloid asphaltene and wax heavy oil colloid) and a large number of chemicals.
Toward a sewage treatment station the processing conditions of the whole system, sulphur content on the high side, in addition to the suspended solid is slightly overweight, oil content and particle size of the median fair meet back injection water quality control index of low permeability reservoir, namely: 8 mg/L or less oil content, suspended solid 3 mg/L or less, the median particle size 2 microns or less.Median particle size does not meet the extra-low permeability reservoir water flooding back water quality control indicators, namely: 5 mg/L or less oil content, suspended solid 1 mg/L or less, suspended solid grain size median 1 microns or less.In view of the suspended solid and practical standards are difficult problems, need for existing in a sewage treatment station, used to study the treatment process, suspended solids in the wastewater and particle size value in the standard treatment is the focus of the next step research.

The experimentation has been carried out with DSC Q 200 F3 Maia, on a number of samples to measure specific heat functions.
It has been reported in the literature that, by increasing Graphite content in the composite matrix leads to grain refinement for Aluminium and eutectic Silicon and porosity.