Search results

EPMA analysis and thickness of trivalent chromium coatings with difference main salt Fig. 3 and Table 1 showed the potentiodynamic polarization curves and data for the coatings deposited at various concentrations of main salt, respectively.
The hardness value of as-deposited and 400°C -heated trivalent chromium coatings Fig. 7 and Table 2 showed the SEM images and wear test data of as-deposited and as-annealed coatings.
Chuang: Huo Role of nickel undercoat and reduction-flame heating on the mechanical properties of Cr–C deposit electroplated from a trivalent chromium based bath, Surface & Coatings Technology, Vol. 203(2009), p. 2921-2926

Data reduction.
By averaging three sets of data, we can determine the K value to be 0.11 and the n value to be 0.62, indicating the pseudo-plastic behavior for film foam flow in a vertical tube.

This phenomenon can be unfavorable to health, safety, and the environment; it can also affect rubber performance such as weakening of adhesive properties and reduction of tackiness [9].
There is also scarce data on NR vulcanizates employing surfactants in their formulation [13].
The correlation between blooming and tensile properties of NR vulcanizates at 50 °C is then investigated from the gathered data.

The DM642 processes the data of the image on time, it sends the control signal to CPLD which has the extend IO according to the result [2].
The EMIF has 4 enable signals which are consisted of CE0, CE1, CE2 and CE3.CE0 is configured for 64-bit wide SDRAM, CE1 is configured as 8-bit asynchronous memory interface and has been allocated to FLASH, CPLD, and SDRAM.CE0 space is configured for 64-bit SDRAM interface, allocated to the expansion of the use of SDRAM, used to store programming and data.
The edge information is also obtained to reserve as the noise reduction image processing.

The observed decrease of metal-insulator temperature (TIM) with the reduction of average radius of A places was explained by the narrowing of the bandwidth due to a bending of the MnOMn bond angle [3, 4].
The XRD data were handled with Checkcell program.
The results of calculus of magnetic molar moment, based on ferrimagnetic model, are not in agreement with experimental data [7].

The temperature parameter method [5], in which the temperatures of the structures are used as the optimization variables, can satisfy the constraint conditions (6c, d) automatically and is beneficial because of its reduction of variables.
The interface strength is considered by using the proposed interface failure criterion (11) and the interface parameters are 0.124 mi S σ σ= and 0.0517 mi S τ σ= , which are obtained by regressing the experimental data of Sun et al.[6].
The computational results show good agreement with the experimental data and illustrate the validity of this method.

A large number of experiments prove that as the reduction of wall thickness of the blade, then rigidity reduces and machine stability reduce, which affecting the part machining quality and processing efficiency.
The main experimental equipments are Dytran 5850B hammer,Dytran 3055B acceleration sensor and DEWE3010 data acquisition system, and the test principle is shown in Figure 4.
In order to ensure the accuracy of experimental data, the acceleration sensor must be fixed on the same position when the cutting each area is completed.

The cold chain facilities in construction or in use lack of consideration for energy conservation and emission reduction.
Computer-based management information system and electronic switching system should be established with unified data to achieve a full dynamic monitoring of refrigerated truck and to simplify links such as transportation plans, approval process and the deployment of empty trucks.
(4) Products development and experimental verification Because of the backward development technology and test means, design optimization, data analysis and the cost comparison of the domestic refrigerated truck are unavailable temporarily.

Recently, the researchers focus on reduction of power processing stages in order to optimize the circuit performance.
Fig. 9 shows the variation of the solar irradiance and temperature based on the real environment data taken from data logger.

Conclusion The presented data indicate the necessity to protect boron from gases dissolved in the molten steel, such as oxygen and nitrogen, in order to prevent the formation of persistent compounds and reduction of the “effective” boron concentration, which increases the hardenability of steel.
The obtained data indicate that in a high strength state, the increased content of harmful impurities and nonmetallic inclusions is particularly dangerous, as well as nitrogen, which increases the tendency of the steel to brittle fracture.