Search results

According to the knowledge of textile materials, comfort performance generally include three aspects: health comfort, sports comfort and appearance comfort[1,2].
Materials and Experiment Methods Materials, Reagents and Instruments Cochineal red, safflower yellow, gardenia blue, disodium hydrogen phosphate, citric acid and silk crepe de chine.
Lu: Food Science. 59-64 (2008)
Tang: Textile Dyeing and Finishing Journal. 32-35 (2011)
Zhang: Journal of Textile Research. 13-15 (2004).

To compare the two materials, process simulations for ethane was implemented.
Ali Jazayeri, et al.: Journal of Natural Gas Science and Engineering, Vol. 2(5) (2010): p217 [6] M.
Yang, et al.: International Journal of Hydrogen Energy, Vol. 35(13) (2010): p7236 [9] H.
Liu: Applied Mechanics and Materials, Vols. 90-93(2011): p3026 [10] H.M.
Sun: Applied Mechanics and Materials, Vols.170-173(2012): p2489

Test Scheme Raw Materials.
Asphalt mixtures belong to viscoelastic plastic materials, the influence of temperature on asphalt mixtures is very significant.
Asphalt viscosity was decreased with increasing temperature, the cohesion of asphalt mixture materials were also decreased, it is the main influence factor on leading to greatly reductions of anti-shear strength of asphalt mixtures.
The interlock of aggregate is the main factor of internal friction angle of asphalt mixtures, so the influence of temperature on internal friction angle φ of materials is not obvious.
References [1] Jin-an Shen: Road Performance of Asphalt and Asphalt Mixture (China Communications Press, Beijing 2001) [2] Zhenglan Lu, Lijun Sun: Journal of Tongji University (Natural Science) Vol.35 (2007), p.1476, In Chinese [3] W.D.O Paterson.

TG curve of modified Hitec molten salt Latent heat of molten salts was also one of the important characteristics for thermal storage materials, therefore, molten salt s were researched by DSC analysis.
Acknowledgements This work was financially supported by National Science Foundation of China under Grant No.51161022 and No. 51303078 and the Science and Technology Foundation of Department of Education of Jiangxi Province, China.
High-temperature thermal stability of molten salt materials.
Testing of thermocline filler materials and molten-salt heat transfer fluids for thermal energy storage systems in parabolic trough power plants.
Journal of solar energy engineering, 2005,127(1): 109-116 [12] Reg.

· Laser intensity: The laser has to be capable of scanning many different materials, which include characteristics such as color, material finish, surface quality and surface reflectivity.
The usual value of minimum signal strength is 50 when scanning shiny materials the peak might not reach 50 so a smaller value is recommended.
The industrial partner implanted following activities: · Geometric benchmarking: suspension layout, number of parts materials used and fitment sequences were identified
Thompson, “Predicting product aesthetic quality using virtual environments,” Journal of Computing and Information Science in Engineering,Vol. 1(2), 2001, pp. 105–112
Humphreys “Early supplier involvement in the design process:lessons from the electtronics industry,” The international Journal of Management Science, 2004, pp.179-199

(b) During laser re-melting, the coatings of Al2O3/Cr compound materials produce analogous martensitic phase transition, therefore, the strengthening of Al2O3/Cr compound material by laser re-melting comes from fine-grain strengthening by Cr-alloy martensitic phase transition partly
(2) The main strengthening mechanism of metal-based compound materials is that the load is transferred to reinforcement from the substrate, and reinforcement is a primary undertaker of load, the mechanism of load transfer is a key strengthening factor.
Zhuang: Ordnance Material Science and Engineering Vol. 23 (2000), p.7
Zhao: Laser Journal, Vol. 25 (2004), p.76
Chen: Journal of the Chinese Ceramic Society, Vol. 28 (2000), p.133

It is one of the strongest building materials, with a tensile strength that rivals steel and weight-to-strength ratio surpassing that of graphite.
The fact that bamboo is not fully utilized in modern structures is due largely to the lack of validation based on the theory of mechanics, material science, structural design and testing [2].
These properties when combined, suggest that bamboo will make a fine addition to the selection of potential reinforcement bar materials.
Especially in many parts of underdeveloped rural area, conventional construction materials such as steel are not only expensive but also difficult to obtain.
Thus, it would be expected that the low-cost bamboo reinforced concrete materials have a wide market in future time in building structures.

The theoretical similar relationship is deduced by using the dimensional analysis and the physical dimensions are the controlling factors if the materials and other factors keep the same.
The dynamite for explosion is set right over the top of tunnels and explosive materials are ordinary TNT.
Conclusions When the materials for models and the parameters for dynamite keep the same the similar theory is suitable for analyzing the displacements of tunnels under explosion.
Hefei：University of Science and Technology Press [2] Zheng Z.M., Yang Z.S. (1981): Explosion Working.
Chinese Journal of Underground Space and Engineering, 3(6):1077-1080.

Nunes, “Properties and Selection: Nonferrous Alloys and Special-Purpose Materials”, ASM Handbook, ASM International, Vol 2, (2004)
Nogi, “Effect of Tool Shape on Mechanical Properties and Microstructure of Friction Stir Welded Aluminum Alloys”, Materials Science and Engineering, PP. 25-31, (2006)
Murr, “Corrosion of Friction Stir Welded Aluminum Alloys 2024 and 2195”, Journal of Materials Science Letters, PP. 2117-2122, (2000)
North, “Effect of Welding Parameters on the Strain Rate and Microstructure of Friction Stir Spot Welded 2024 Aluminum Alloy ”, Journal of Material Science, PP. 5589-5601, (2007)
Lee, “Microstructures and Failure Mechanisms of Friction Stir Spot Welds Aluminum 6061-T6 Sheets”, Journal of Materials Processing Technology, PP. 291-297, (2006)

After estimating the quantities of major building materials required in a building, the energy cost of these materials is assigned to the estimated quantities.
Some of the materials with low EE are discussed below.
Sustainability in human settlements: imminent material and energy challenges for buildings in India, Journal of the Indian Institute of Science, 92, 2012, p. 145–162
Construction Materials, 160, 2007, p.135-143
Insulating Materials for Energy Saving in Buildings, Trans Tech Publications, Switzerland, under Key Engineering Materials, doi: 10.4028, Vol. 632, 2015, p. 1-14.