Search results

Acknowledgment This research is supported by LIMPID 7 FP Collaborative European Project Nanocomposite Materials for Photocatalytic Degradation of Pollutants NMP 2012.2.2.2-6 (no. 310177) and Silpakorn university.
Grätzel, Journal of the American Chemical Society 127 (2005) 16835-16847
Lobmann, Preparation of TiO2 thin films on polystyrene by liquid phase deposition, Journal of Materials Chemistry 13 (2003) 1058-1063
Vaia, Assemblies of titanium dioxide-polystyrene hybrid nanoparticles for dielectric applications, Chemistry of Materials 22 (2010) 1749-1759
Palacin, Grafting polymers to titania nanoparticles by radical polymerization initiated by diazonium salt, Journal of Material Science 46 (2011) 6332-6338

The procedure to calculate materials parameters from bulge tests is shown in Figure 1(b).
Materials parameters of strain rate sensitivity and strength coefficient have been calculated from the log-scaled plot of stress vs. strain rate in Figure 4(b).
Materials parameters obtained from tensile and biaxial testing are shown in Table 1.
Jovane, An approximate analysis of the superplastic forming of a thin circular diaphragm”, International Journal of Mechanical Science 10 (1968) 403
Mukherjee, Superplastic forming: an analytical approach, Material Science and Engineering A157 (1992) 9.

Introduction In many applications of ferromagnetic materials both the magnetic properties and also the mechanical properties of these materials are important.
The majority of magnetic materials, such as ferromagnetic metals, and alloys of metals and ceramic materials, show small susceptibility to deformation, and are also frequently brittle [1] .
Materials Science and Engineering (2000), p.89-100
Chinese journal of physics Vol. 38, N°2-I April 2000
New Journal of Physics 5 (2003) p.1-10

Jia: Polymer Materials Science Engineering Vol. 26 (2010), p. 39, in Chinese
Zong: Polymer Materials Science Engineering Vol. 26 (2010), p.125, in Chinese
Xu: International Journal of Modern Physics C Vol. 17 (2006), p.771
Gladrow: Journal of Statistical Physics Vol. 79 (1995), p. 1023
Succi: International Journal of Modern Physics C Vol. 9 (1998) p. 1405

A 4340 steel is used to model the material of container.
Journal Of Ordnance Engineering College, 2001, 13(3)
Journal of Ordnance Engineering College, 2002,14(2)
Journal of Beijing Institute of Technology, 1999,19(S1)
Beijing: Science Education Book press, 2003.

The carbon-based nanodots usually prepared by mean of such as purification or isolation process of short carbon nanotubes to nanotubulars [9], chopping graphene sheet or graphene-based materials into nano-sized fragments [10, 11].
Acknowledgements The authors thank the Faculty of Biomedical Engineering, Rangsit University and the division of Science, Faculty of Science and Technology, Rajamangala University of Technology Phra Nakhon (RMUTP).
Pechprasarn, Graphene-Based Materials for Biosensors: A Review, Sensors (Basel) 17(10) (2017)
Qu, Recent advances in graphene quantum dots for sensing, Materials Today 16(11) (2013) 433-442
Feitosa, Novel and Fast Microwave-Assisted Synthesis of Carbon Quantum Dots from Raw Cashew Gum, Journal of the Brazilian Chemical Society (2015)

The screw conveyor can satisfy the long distance transmission of materials, and can blend and mix the material in certain working conditions.
Journal of China Coal Society, 2010, 35(3):498-502
Coal Science and Technology, 2006,34(8):8-10
Journal of Jiangsu University of Science and Technology, 1996, 17(5):1-9
Li, et al: Genetic algorithm toolbox and application(Publication of Xian University of Electronic Science and Technology, Xian, 2005).

Experimental (1) Raw Materials.
Journal of Optoelectronics & Advanced Materials, 2007, 9(10):3061-3063
Journal of Materials Science & Technology, 2020, 43:32-39
Key Engineering Materials, 2016, 702:96-100
Korean Journal of Materials Research, 2008, 18(12):678-682.

Materials Science Forum2007:753-756
Journal of Electronic Materials35.8(2006):L11-L14
"Ultraprecision CMP for sapphire, GaN, and SiC for advanced optoelectronics materials." 
Advanced Materials Research 797(2013):284-290
Comparison of Fe catalyst species in chemical mechanical polishing based on Fenton reaction for SiC wafer Advanced Materials Research.

Experimental materials and methods Mg-8.9wt%Al-0.53wt%Zn alloy cast ingots (direct casting and air cooling) with an outer diameter of 160mm are adopted as the materials for experiment.
So, the tensile strength of the material becomes less than that when the temperature is 390 ºC, the plasticity of the material decreases continuously.
References [1] H.T.Zhou, C.J.Ma, X.Q.Zeng, W.J.Ding: Materials Review, Vol.17-11 (2003), p.16 [2] T.
Diaka: Materials Science and Engineering A, Vol.496 (2008), p.247 [7] Q.Guo, H.G.Yan, Z.H.Chen, H.Zhang: Journal of Plasticity Engineering, Vol.7 (2006), p.739 [8] P.
Uchida: Materials Science and Engineering, Vol.434 (2006), p.131 [10] M.Shahzad, L.Wagner: Materials Science and Engineering A, Vol.506 (2009), p.141