Search results

Introduction In the past decade, the use of inorganic filler to improve the physical properties of polymer composites has become widespread in the production of high-performance materials.
Experimental Materials.
Dibenedetto: Journal Material Science Vol.30 (1995), p.2438
Yoon : Journal Applied Polymer Science Vol.78 (2000), p.1267
Journal of Polymer Degradation. & Stability Vol.83 (2004), p.411

Introduction Nickel is categorized as one of few materials that have small lattice mismatch with diamond.
With this growth type, interfacial stresses between the two materials upon coaling down from deposition temperature can be relieved which prevents coating cracks and delamination [2].
Prater, Hetero-epitaxial nucleation of diamond on nickel, Diamond and Related Materials. 7 (1998) 276-282 [2] P.
Callister, Jr., Material Science and Engineering an introduction.
Growth of diamond films on copper, Journal of Materials Research. 9 (1994) 921−926

Introduction Water quenched blast furnace slag (GBFS) is main cementitious material of NSC, it accounts for 80%-90% of non-clinker slag cement.
Experimental methods raw materials and mixing ratio.Main component of cementitious materials is GMFS and phosphorus gypsum which alkalinity is greater than 4.5, vitrification-ratio is greater than 98.5%.
Mineral composition of raw materials and physical property follows in Table 1.
NSC’s bleeding-water phenomenon slightly larger than the OPC, it caused by early hydration rate is relatively slows than OPC.Excessive bleeding-water may lead to the material layered segregation, it not only affect the concrete’s early strength and long-term strength, but also directly affect the long-term durability of the structure.
I [2] I.A.Voinovichetal:Silicates Industriels Vol. 209-212 (1976),p.41 [3] Yingmo Piao: Journal of Yanbian University natural science Vol. 220-224 (2003),p.29 [4] Yi QIN, Yingmo Piao: Journal of Liaodong University natural sciences Vol. 22-4 (2007),p.14 [5] Yingmo Piao:Proceeding of Korea Architects Institute Vol. 143-150 (2001),p.17 [6] Yingmo Piao:Journal of Harbin Institute of Technology Vol. 210-213 (2009),p.41

A retrievable polymer urethral stent for treatment of urethral strictures Ziqiang Zhang1 , Kun Hu 1, Hong-Xu Huo3, Kang-Ning Chen4, Bo Meng 2, Fu-Zhai Cui2 * 1 Beijing Allgens Medical Science & Technology Co., Ltd, Beijing, 100085, China 2 Department of Materials Science & Engineering, Tsinghua University, Beijing, 100084, China 3 Department of Urology, Hebei Medical College Second Hospital, Shijiazhuang 050000, China 4 Department of Urology, Hebei Province People Hospital, Shijiazhuang 050051, China Keywords: Urethral stricture; Stent; Poly (l-lactide) Abstract This paper reported a newly designed retrievable urethral stent used in treatment of urethral strictures.
Materials and methods Device Material.
Journal of urology, 2000, 163: 773-776
British journal of urology, 1996, 77: 701-704
Journal of interventional radiology,1999,18(1):56-57

Titanium alloy TC4 is a kind of α + β alloy, certain characteristics, however, such as low thermal conductivity, strong chemical reactivity with the cutting tool materials at high temperatures, and relatively low elastic modulus, make it one of the classical difficult-to-cut materials[3].
This is mainly because of big brittleness and high hardness of the CBN cutting tool material itself, and the micro defects of materials inside.
New York:The Materials Information Society,2000
CIRP Journal of Manufacturing Science and Technology, 2008, 1 (1): 81-85
International Journal of Machine Tools & Manufacture, 2009, 49 (7-8): 561-568.

Introduction Along with the development of the automotive lightweighting design, lots of advanced lightweight materials were widely applied, such as aluminum alloy, magnesium alloy [1].
The hardness of clinched joint materials is 799.24HV after local thermal treatment, increasing by 77.78%.
Journal of Machine Design,2013,30(9):78-81.
Materials and Design, 2011, 32(10):4943-4954
Journal of Materials Engineering and Performance, 2012,22(1): 294-299

Then, Polyoxyethylene (Poly ethylene Oxide (PEO), Tianjin Dadi fine chemical engineering company, Mw=300000) solution is used electrospinning materials in this paper.
Taylor cone and jetting from liquid droplets in electrospinning of nanofibers, Journal of Applied Physics, 90(2001), 4836-4846
Precision deposition of a nanofibre by near-field electrospinning, Journal of Physics D-Applied Physics, 43(2010), 415501
Wallace. 3-dimensional (3D) fabricated polymer based drug delivery systems, Journal of Controlled Release2014), [7] K.
Bionic electrospun ultrafine fibrous poly (L-lactic acid) scaffolds with a multi-scale structure, Biomedical Materials, 4(2009), 035004

Materials and Methods Synthesis of photocatalyst.
Acknowledgement The authors thank Research Management Institute (RMI), Universiti Teknologi MARA (UiTM) and Ministry of Science, Technology and Innovation of Malaysia for the financial suort through e-Science Grant No: 100-RMI/SF 16/6/2 (19/2012).
Chu, A review of photocatalysts prepared by sol gel method for VOC removal, Molecular Science, 11 (2010) 2336-2361
Materials Research, 894 (2014) 245-249
Rabbani, Comparison of photocatalysis degradation of 4-nitrophenol using N,S co-doped TiO2 nanoparticles synthesized by two different routes, Journal of Sol-Gel Science and Technology, 64 (2012) 17-26.

These materials are all remarkably damage tolerant.
Vol.2 Materials and Properties.
Hultman, The Mn+ 1AXn phases: Materials science and thin-film processing.
Fracture toughness of alumina matrix composites (AMC) Journal of Optoelectronics and Advanced Materials 12, 2 (2010) 301 - 308 [11] S.
Materials Science (Medžiagotyra). vol. 19, No. 4, 2013, 367-372

Materials and Methods Sample Collection and Detecting.
Song, Journal of Lake Sciences Vol. 18 (2006), p. 150 [3] J.
Zhang, Journal of Lake Sciences Vol. 22 (2010), p. 70 [12] N.
Wei, Journal of Lake Sciences Vol. 22 (2010), p. 723 [14] M.
Yu, Journal of Natural Disasters Vol. 17 (2008), p. 134 [15] Z.