Search results

Magnetic soft-hard composites, combining the hard magnetic properties such as high coercivity with the high saturation magnetization achievable in soft magnetic materials, are potential materials for MEMS/NEMS.
Nelson, Electrodeposition of low residual stress CoNiMnP hard magnetic thin films for magnetic MEMS actuators, Journal of Magnetism and Magnetic Materials 292 (2005) 49-58
Cho, Study on advanced multilayered magnetostrictive thin film coating techniques for MEMS application, Journal of Materials Processing Technology 201 (2008) 678-682
Ataie, Synthesis of Nanocrystalline Barium Ferrite in Ethanol/Water Media, Journal of Materials Science and Technology, Vol.25, No.4 (2009) 465-469
Sumodjo, Development of electroplated magnetic materials for MEMS, Journal of Magnetism and Magnetic Materials 265 (2003)189-198

Iron, calcium, and lutetium oxides are considered contamination which can be reduced by using high pure materials.
Those materials were not used in the present work since we were only investigating the process parameters.
Figure 1 shows the micrographs of the starting materials after milling in different conditions.
These materials can be considered potentially useful for applications in radiotherapy treatment.
M. – “Glass and Medicine” - International Journal of Applied Glass Science – 2010 [12] Sene F.

Shi: A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends (Journal of Materials Science & Technology 2019, 35 (2), doi: 10.1016/j.jmst.2018.09.004) [2] Z.P.
Kumar: Study of Microstructure and Mechanical Properties of As-built and Heat-treated Additive Manufactured Inconel 718 Alloy (ASEAN Journal on Science and Technology for Development 2021, 38 (3), doi: 10.29037/ajstd.724) [5] M.
Niu: Comparison of microstructures and mechanical properties of Inconel 718 alloy processed by selective laser melting and casting (Materials Science and Engineering: A 2018, 724, doi: 10.1016/j.msea.2018.03.073)[7] H.
Long: Mechanical behavior of additive manufactured, powder-bed laserfused materials (Material Science and Engineering 2016, 651, doi: 10.1016/j.msea.2015.10.068) [9] S.
Nath: Effects of different surface modifications on the fatigue life of selective laser melted 15-5 PH stainless steel (Materials Science and Engineering: A 2019, 762, doi: 10.1016/j.msea.2019.138109)

Introduction The importance of polymer blending has been increased in recent years, because of the preparation of polymeric materials with desired properties, low basic cost, and improved processability[1-3].
Experimental Materials.
FT IR spectroscopy is a useful tool in determining specific functional groups or chemical bonds that exist in a material.
Miscibility study of chitosan/polyethylene glycol fumarate blends in dilute solutions, Journal of Applied Polymer Science, Vol. 127 (2013), p. 3514-3521
Miscibility studies on the blends of collagen/chitosan by dilute solution viscometry, European Polymer Journal, Vol. 43 (2007), 2066-2071.

Introduction The modernization of material distribution is the direction of the future development of enterprises.
The forklift,which has the compact structure and the flexible operation, is the main tool for materials handing.
  [2] Beijing materials handling research institute, The Collection Of forklift's standard [M], China Machine Press, 1990: 205-208
"Model of case-based Industrial design scenario and its application", Chinese Journal of Mechanical Engineering, 2006, 42(12), 151-157
Journal of System Simulation, 2007, 19(12): 2720-2722

Determination Methods Materials.
Journal of food engineering. 
Chinese journal of analysis laboratory.
Chemical Journal of Chinese Universities.
Journal of Yunnan Nationalities University: Natural Sciences Edition, Vol.3(1994), p.20-23 (in Chinese) [14] QZ Meng, CR Li, YH Dong and CS Zhou.

They have tested lots of SS316NG and SS304 materials in light water reactor (LWR) of various operating conditions [4-7].
It would be the best policy to test the real material used in NPP, however, no test material is available in the vendors'.
So the test material block was made in a local steel company.
Acknowledgments This study was done as a partial project of "Development of Periodic Safety Review Technology or Nuclear Power Plants" funded by the Ministry of Science and Technology in Korea, titled "Development of Aging Management Technology."
Itatani, et.al: Fatigue Crack Growth Curve for Austenitic Stainless Steels in BWR Environment, Journal of Pressure Vessel and Technology Vol. 123 (2001) [5] W.

Most of the current studies are based on the meso-acoustic model to analyze the effect of equivalent diameter of voids on the sound absorption performance of porous materials, and the equivalent diameter of voids here is the average of all equivalent diameters of voids, which is only statistically significant.
Specimens Shaping and Measurement of Sound Absorption Coefficient Materials.
Optimization of Pore Structure of Acoustic Porous Materials, Journal of Xi'an Jiaotong University, 2007(11): 1251-1256
The grey system theory tutorial, Wuhan: Huazhong University of Science and Technology Publishing, 1990
Analysis of Factors Affecting Water Stability of Asphalt Stabilized Macadam Based on Grey Entropy Method, Journal of Chongqing Jiaotong University (Natural Science),2008, 27(06): 1077-1080

Materials and Methods Microorganism The wild type strain of Aspergillus niger was collected from the Department of Microbiology, University of KwaZulu-Natal, South Africa.
Journal of American Science, 6 (2010)1222–1229
Journal of Food Science and Technology, 47 (2010) 365–371
Journal of Applied Sciences, 7 (2007) 3687–3695
Journal of Dairy Science, 41 (1958) 1683–1692

Introduction Sawing with segmented diamond sawblades is the most widely used process for natural stone and other construction materials.
Many previous studies on the grinding of brittle materials with diamond mentioned the dependence of tool wear on the temperatures generated in the wheel-workpiece contact zone [1].
For grinding and sawing of granite materials, however, what is of most concern is the wear of the diamond tools rather than the thermal damage to the workpiece.
Luo: Journal of Materials Science Vol. 1245(51) (1993), p. 28 [3] W.
Xu: Key Engineering Materials Vol. 375-376 (2008), p. 549 [8] W.B.