Search results

National Natural Science Foundation of China（50965012） References [1] X.C.Zhang:Journal of Shenyang University of Technology Vol.31(2009)No.2,p.173
[2] G.Mahendran,S.Babu,and V.Balasubramanian:Journal of Materials Engineering and Performance Vol.19(2010)No.5,p.657
[3] M.Zebardast and A.Karimi Taheri:Journal of Materials Processing Technology Vol.211(2011) No.2,p.1034
[5] Behcet Gulenc: Journal of Materials and Design Vol. 29 (2008),p.275
[6] W.P.WENG and T.H.CHUANG:Journal of Metallurgical and Materials transactions Vol.28 (1997),p.2672.

Three types of materials as stated previously were detected within the profile.
Three types of materials as stated previously were detected within the profile.
Chandak (2011): Correlation between vertical electric sounding and conventional methods of geotechnical site investigation, International Journal of Advanced Engineering Sciences and Technologies, 4, 042-053
Simons: Site Investigation (Blackwell Science Ltd, UK (1995)
Al-Arifi (2010): Integrated geoelectrical survey for groundwater and shallow subsurface evaluation: case study at Siliyin spring, El-Fayoum, Egypt, International Journal of Earth Sciences, 99, 1427-1436

However, in the almost ME materials, the ME effect operate only far below room temperature and/or in the too high magnetic field for applications.
Acknowledgments This work was supported in part by Japan Society for the Promotion of Science (JSPS) KAKENHI (Grant No. 23760641) and Nippon Sheet Grass Foundation for Material Research.
Kimura: Nature Materials, Vol. 9 (2010), p.797
Ikeda: Materials Research Bulletin, Vol. 46 (2011), p.1085
Lin, Linfeng Chen: Journal of Magnetism and Magnetic Materials, Vol. 310 (2007), p145 [5] T.

The resulting microstructure depends on material’s heat treatment and alloying.
For this reason, it is beneficial to use material-technological modelling in a thermomechanical simulator (Fig. 2).
Fucheng: Inconsistent effects of mechanical stability of retained austenite on ductility and toughness of transformation-induced plasticity steels, Materials Science & Engineering A, 2013, vol. 578, pp. 370–376
Jirková, et al.: Influence of metastable retained austenite on macro and micromechanical properties of steel processed by the Q-P process, Journal of Alloys and Compounds, available online, Journal of Alloys and Compounds, 615 (2014) pp.163–S168
Materials Science Forum, 2010, vol. 654-656, pp. 94-97

Halitov, Modeling of a reduction zone of the gasifier installation, Materials Science and Engineering, 124, (2016) [4] D.V.
Saprykina, The development of equipment for the disposal of solid organic waste and optimization of its operation, Materials Science and Engineering, 142, (2016) [6] D.V.
Mokhovikov, Mathematical modeling for the development of equipment for thermochemical processing of wood waste in to dimethyl ether, Materials Science and Engineering, 142, (2016) [8] Y.
Kapustin, Equipment for the production of wood-polymeric thermal insulation materials, Materials Science and Engineering, 142, (2016) [13] B.
Luible, Supporting the development process for building products by the use of research portfolio analysis: A case study for wood plastics composite materials, Case Studies in Construction Materials, 4 (2016) 49-54

Introduction Approximately half of the global electric energy produced today is used in motors and the increasing necessity of energy conservation brings the interest in the development of high performance magnetic materials.
Cullity, Introduction to Magnetic Materials, first ed., Addison-Wesley Publishing Company, Massachusetts (1972)
Watanabe: Journal of Materials Research Vol. 13 (1998), pp. 457-461
Wada: Journal of the Magnetics Society of Japan Vol. 24 (2000), pp. 651-656
Zhai: Journal of Materials Science Vol. 47 (2012), 4110-4117

Fig..1 - Typical Open Pit Mining Cost Breakdown Bulk materials in mining are transported by haulage, whereas in surface mining this task is executed in the most part of cases by trucks and conveyors.
Bibliographic review In many industries, materials handling represents a significant component of the operational cost, making equipment selection an important challenge to management (Caccetta et al).
Once these parameters are usually distinct for different materials inside the mine, the application search divides the analysis in two perspectives: ore and waste.
Burt: An optimization approach to materials handling in surface mines.
Department of Energy science and Engineering, Indian Institute of Technology Bombay, India 2010

Materials and Methods 1.1 Study Site The experiment was organized at the Sanjiang Mire Wetland Experimental Station(47°35’N, 133°31’E), Chinese Academy of Sciences.
Li: submitted to Journal of Hydrology (2002) [2] W.J.Liu, J.M.
Duan: submitted to Journal of Natural Resources (2001) (in Chinese) [3] Y.H.
Deng: submitted to Journal of natural resources (2004) (in Chinese) [5] Z.Q.
Sun: submitted to Wetland Science (2006) [6] B.X.

Finite Element Analysis Model Material models.
Acknowledgements The work presented in this paper was funded by National Science Fund (51108399) and Shandong College and University S&T Planed Projects (J11LE11), and Shangdong Science Fund (ZR2011EL046).
Journal of Ship Mechanism.
International Journal of Impact Engineering.
International Journal of Impact Engineering, Vol. 27(2002), p.669

They can be used to machine very hard materials such as sintering alloy, CBN, optical glass, engineering ceramic and so on.
Acknowledgement Sustentation of National Nature Science Funds [No. 50375096 ] Reference [1] Brian K.
Scattergood: International Journal of Machine Tools & Manufacture, Vol.42 (2002), pp.1355-1362
Rahman: International Journal of Machine Tools & Manufacture, Vol.42 (2002), pp.935-943
Incropera: Transactions ASME Journal of Manufac-turing Science and Engineering, Vol.123 (2001), pp.639-646.