Search results

The material was steam, the density of which is set to be ideal compressible gas.
Jiang: Journal of Power Engineering.
Chen: Atomic Energy Science and Technology.
Inada: Journal of Fluids and Structures.
Zhang: Journal of Zhejiang University SCIENCE A.

Introduction Polyacrylonitrile (PAN) fibers are widely used as textile material because of their cheap price.
Experimental Materials.
Journal of Applied Polymer Science, 1997,65(5): 959-966
Journal of Materials Science, 2005,40(20): 5355-5358.

Fork joint material is set as 40CrMo, parameters are: elasticity modulus E = 2×1011 Pa, Poisson ratio μ= 0.3, yield limit σs=500 MPa, shear modulus E=2×109 Pa.
Fork joint material is set as ZG40CrNiMo, yield limit σs=700 MPa, fork joint has yield, and from fig 4 we can obviously see that it yield in a large range.
It can be concluded that fork joint material yield before transfer torque reach rated torque, load capacity cannot reach rated torque.
(Natural Science Edition), 2008 , 31 (1) 32 —36
JOURNAL OF ENGINEERING GRAPHICS. 2011(02)

Adsorption of Organic Substances on Modified Montmorillonite, Cloisite 10A, 15A, 20A, 25A, and 30B Tarinee Nampitch 1,a 1 Department of packaging technology and materials.
Ratanarat and coworker, 2003. [1-8] Experimental Materials Organoclay, Cloisite 10A, 15A, 20A, 25A and 30B, were supplied by Southern clay Inc., USA.
Material Testing The dried rubber sheet was characterized by tensile test and Thermogravimetric analysis (TGA).
Ohshima: Journal of Colloid and Interface Science.Vol. 178 (1996), “Surface Structure of Natural Rubber Latex Particles from Electrophoretic Mobility Data”, 442-445
Leite, and Fernando Galembeck: Journal of Colloid and Interface Science.

FE Analysis Constitutive relationship of materials.
Adhesive material is an elastic material based on Quads damage criteria..
Acknowledgments The authors gratefully acknowledge the financial support provided by the National Natural Science Found (Project No.10802023, 50808085, 10672060), the Guangdong Yuang scholars Science Found (Project No.
Qiao: International Journal of Solids and Structures, Vol. 46 (2009), p. 2618 [2] J.F.
Ehsani: ACI Structural Journal, Vol. 95 (1998), p. 142 [5] P.

Because of the toxicity and material compatibility problems associated with the cyanide bath, the non-cyanide electroless gold plating has become a hot research topic [2-4].
The paper is supported by the National Natural Science Foundation of China under Grant nos. 51172097 and 51272090.
Yuasa: Journal of the Electrochemical Society, Vol. 153 (2006) No.1, p.63
Kato: Science and Technology of Advanced Materials, Vol. 7 (2006) No.7, p.425
Okinaka: Journal of the Electrochemical Society, Vol. 144 (1997) No.4, p.3462

Thermal Design, Analysis and Verification of Chip-Level MCM with Properties of Semiconductor Materials JunHui Wu 1,a , Quan Zhou 1,b , Qiang Zhou 2 ,c*, Jie Chen 1,d HuiPing Si 1,e, KaiYan Lin 1,f and ChiBin Zhang 3,g 1Institute of Modern Agricultural Science & Engineering, Tongji University, 4800 Caoan Hwy, Jiading, Shanghai, P.R.
The results of finite element analyses showed the reasonableness of the design of MCM, and combined with the different substrate materials and circuit board materials, further discusses about improved cooling capability of MCM were expressed in this paper.
Only replace the materials of the MCM chip circuit board with the printed circuit board of high thermal conductivity which is made by the T-Lam system.
To improve materials of MCM substrate, AIN and CVD had been used to make MCM substrate in this paper, and modeling analysis of these two MCM was done in ANSYS.(1) Substrate of AIN.
Journal of Dalian University of Technology. 2005, 45(3): 320-325

A study on material performances of cylindrical concrete specimens confined by carbon fiber-reinforced polymer at a strain rate of about 0.1/s has been made in reference[1], while materials may bear higher strain rate under blast and impact loading.
Basalt continuous fiber and its hybrid materials[J].
High-tech fiber and its hybrid materials, 2002, 27(2): 1-5 [3] Lei Su, Zhoudao Lu, Kechun Zhang, et al.
Experimental study on BFRP-reinforced pre-damaged concrete column-beam joints by simulated earthquake[J].Journal of Southeast University (Natural Science Edition),2010,40(3): 559-564 [4] Li'an Shi, Haiyan Ma, Zhidan Rong.
International Journal of Impact Engineering, 2001,25(9): 869-886 [6] Jinguang Teng, Janfen Chen, S.

An Experimental Study on Oil-air Lubrication of Sliding Friction Element Cailin1, a, Jinli Wang2,b, Hongtao Zheng1,c 1 College of Power Science and Engineering, Harbin Engineering University, Harbin 150001, Heilongjiang, P.R.
Zhong: Ultra-high-speed grinding spindle characteristics upon using oil/air mist lubrication, International Journal of Machine Tools & Manufacture, 2002 No.42 [3] K.
Zhong: Ultra-high-speed thermal behavior of a rolling element upon using oil-air mist lubrication, Journal of Materials Processing Technology，127 (2002) 191-198
Ekeredc: Studies on minimum quantity lubrication (MQL) and air cooling at drilling journal of materials processing technology, 200 (2008) 339-346
[6] Chinese National Standard GB124441.-90, Metallic materials-Wear tests MM mode wear test.

While the transformation superplasticity occurrence depends on the phase transition procedure and it can occur under stress by many times phase transformation but does not necessarily require materials owning ultra-fine grain structure.
Zhou: The Chinese Journal of Nonferrous Metals, Vol. 20 (2010) No.3, p.390-396 (In Chinese)
Cao: Transactions of Materials and Heat Treatment, Vol. 30 (2009) No.6, p.111-115 (In Chinese)
Yang, J.X He: Journal of Materials Engineering, Vol. 11 (1993), p.12-13 (In Chinese)
Zhang: The Chinese Journal of Nonferrous Metals, Vol.14 (2004) No.7, p.1059-1067 (In Chinese)