Search results

Influence of the Binder Amount on the Properties of the Non-Sintering Ti(C,N)-Si3N4-SiC Composite Refractories Bo Tana, Kai Chen, Zhaohui Huangb, Minghao Fang, Yan-gai Liu, Xiaowen Wu School of Materials Science and Technology, China University of Geosciences (Beijing), Beijing 100083, P.
In recent years, researchers have found that the Ti(C,N) would not only enhance the oxidation resistance of refractories, but also improve the corrosion resistance as an additive in refractory material, and prolong the service life of refractory materials [2,3].
In our previous studies [4,5], quartz, rutile and coke were used as raw materials in preparing the Ti(C,N)-Si3N4 composite powders by carbothermal reduction nitridation (CRN) method.
Experimental Starting materials.
Aneziris, Microstructure evaluation of MgO-C refractories with TiO2 and Al additions, Journal of the European Ceramic Society. 27 (2007) 73-78

In addition, no shrinkage self-compacting concrete admixtures are added to enhance the performance of all aspects of reinforcement materials.
The authors would like to thank them for providing all the materials and experimental equipments in the technical program.
(In Chinese) [3] Liangtao Bu, Changsheng Wan, Peng Yin, Journal of Hunan University(Natural Sciences), 37(1) (2010), p. 5.
Scordelis, Journal Proceedings, March 1,64(3)(1967), p. 152
Li, Cynthia Wu, Shuxin Wang, Atsuhisa Ogawa, Tadasgi Saito, ACI Materials Journal/September-October (2002)p. 463.

Introduction The tailings reservoir is important facilities where mine deal with waste, and is widely found in the metallurgical, nonferrous metals, gold, construction materials and other industries, playing very important role in mining production.
Journal of Guilin University of Technology, 4, 783-785, 2006
[9] Huali Qin, Xin Zheng, and Kaili Xu.Journal of Safety Science and Technology, 1,51-54, 2008
[10] China Academy of Safety Science and Technology.
[11] Lihong Yang, Quanming Li, Journal of Safety Science and Technology, 5, 28-31, 2008.

Experimental Materials.
Fig. 3 Temperature dependence of elastic component of dynamic modulus for all materials considered.
Fig. 5 Temperature dependence of dynamic loss modulus, G", for all materials considered.
Plavšić: Polymer Materials Science and Engineering (Naučna knjiga, Belgrade 1995) (in Serbian)
Kraus: Journal of Applied Polymer Science Vol. 39 (1984), p. 75

Thus the other materials of the device are subject to conditions close to the limiting capabilities.
The ceramic materials, including the supporting structure of heating elements, have specific requirements for operating modes and especially the heating rate, also the thermal insulation which should provide sufficient protection of working people.
Of special interest in the study are the temperatures in some specific areas because of restrictive requirements for maximum permissible for the relevant materials value.
Acknowledgment: The present work is supported by the National Science Fund of Bulgarian Ministry of Education and Science, Project DFNI E02/8.
Jitwatcharakomol, “The evaluation of the performance of a glass melting furnace in terms of energy consumption,” Suranaree Journal of Science & Technology, Vol. 21, Issue 1 (2014), p15

Materials and methods The experimental materials used for investigation was Mg-Gd-Y-Zr alloy with different MAO coating for comparison.
Ding, Comparison of biodegradable behaviors of AZ31 and Mg–Nd–Zn–Zr alloys in Hank’s physiological solution, Materials Science and Engineering B. 177 (2012) 395-401
Feyerabend, Degradable biomaterials based on magnesium corrosion, Current Opinion in Solid State and Materials Science. 12 (2008) 63-72
Ding, Microstructure, mechanical properties, biocorrosion behavior, and cytotoxicity of as-extruded Mg–Nd–Zn–Zr alloy with different extrusion ratios, Journal of the Mechanical Behavior of Biomedical Materials. 9 (2012) 153-162
Chu, Corrosion behavior of biomedical AZ91 magnesium alloy in simulated body fluids, Journal of Materials Research. 22 (2007) 2004-2011.

Taking the empirical value of the U.S. as the lower limit of the coefficient of permeability of materials for permeable base and combining the test values of coefficient of permeability of the three gradations in Table 1, the minimum sieve pore shall be ≥1.18mm, and the percentage range shall be = [0,4](%).
b) In terms of bearing capacity, good usability of graded broken stones is ensured by reasonable materials composition design; the shear resistance is particularly important for the deformation stability and overall strength of the basement.
Journal of Shenyang Jianzhu University(Natural Science), Vol. 23, pp.961-964, Nov. 2007 (In Chinese)
Permeability coefficient test of permeable base materials: a case study.
Journal of Chang′an University(Natural Science Edition), Vol. 23, pp.21-23, Mar. 2003(In Chinese)

Chinese Journal of Soil Science.
Applied Mechanics and Materials.
Applied Mechanics and Materials.
Advanced Materials Research.
Advanced Materials Research Vols. 356-360 (2011), p. 2703-2706

Nanoclays are natural or synthetic, cationic or anionic materials.
[4] Evora, V.M.F., Shukla, A., Materials Science and Engineering A361 (2003) p. 358
Torres Marques, "Dynamical mechanical thermal analysis of flame-retardant unsaturated polyester nanocomposites: the effect of aluminium hydroxide (ATH) and nanoclays", Key Engineering Materials, Advanced Materials Forum, 2007
Fan, Journal of Fire Sciences, 24, 2006 [42] Martins M. and C.
Blackwell Science Inc (1999) Cap.8

Dong: Journal of Zhejing University (Engineering Science) Vol. 38(10) (2004), P. 1302.In Chinese
XU: China Safety Science Journal Vol. 13(12) (2003), P. 64.In Chinese
Shen: Journal of Zhejing University (Engineering Science) Vol. 38(19) (2004), P.1325.In Chinese
Luo: Journal of Kunming University of Science and Technology Vol. 25(1) (2000), P.16.In Chinese
Yuan: Journal of Zhejiang University(Engineering Science) Vol. 42(1)(2008), P.4.In Chinese