Search results

Magazine of Civil Engineering. 9(35) (2012) 29-34
Drescher, Modeling test rolling on cohesive subgrades, Advanced Characterisation of Pavement and Soil Engineering Materials.
Series: Materials Science and Engineering. 463 (2018) 1–11
Magazine of Civil Engineering. 4(39) (2013) 35–45
Magazine of Civil Engineering. 5(57) (2015) 45–57

Faculty of Engineering, Materials Engineering Department, Tarbiat Modares University, Tehran, Iran, P.O.Box: 14115-143, Taharostamzadeh@gmail.com 2.
Corresponding author, Faculty of Engineering, Materials Engineering Department, Tarbiat Modares University, Tehran, Iran, shahverdi@modares.ac.ir 3.
Faculty of Engineering, Materials Engineering Department, Tarbiat Modares University, Tehran, Iran, alishanaghi@gmail.com, shanaghi@modares.ac.ir 4.
Zhang, Processing of advanced materials using high-energy mechanical milling.
Forum.

Shang d School of materials science and engineering, University of science and technology Beijing, Beijing 100083 China a wxm@mater.ustb.edu.cn, b hexl@mater.ustb.edu.cn, cyangsw@mater.ustb.edu.cn, d cjshang@mater.ustb.edu.cn Keywords: Ultra-fine bainitic steels, Relaxation-precipitation-controlling phase transformation (RPC), Refinement Abstract.
Fig. 5(c, d) shows the misorientation map of microstructures it can be seen that the boundaries of accicular bainite is large angle boudaries and it has been reported that the three dimentional shape of accicular ferrite is plateplike [12] , therefore the acicular ferrite formed in advance can block effectively the bainite forming in succeeding, and the bainite microstructure will be confined and become finer. 150μm 4μm （a） （c） （b） Fig.4 The dislocation configuration change during the relaxation after 30% deformation at 900℃(a, without relaxation, b, with 200s relaxation, c, EDAX spectrum of precipitates d, e the misorienation distribution map for samples without and with 200s relaxation.
Naval Engineers Journal, Vol. (1990), P.63 [4] H.
He, Materials Science Forum, Vol. 426-432 (2003), p.1307 [11] S.Yang and X.

Periodical edition of the peer-reviewed papers as results of modern scientific research and engineering solutions in the various sectors of engineering sciences.
Materials, Technologies, Biotechnology, Mechanical Engineering, Engineering Management, Environmental Engineering

The composition of the coatings was evaluated by comparing the data obtained using a Versa 3D DualBeam scanning two-beam electron microscope and a Bruker D8 Advance diffractometer.
Wadley, NiAl bond coats made by a directed vapor deposition approach, Materials Science and Engineering: A. 394(1-2) (2005) 43-52
Series: Materials Science and Engineering. 116 (2016) 012018
Shirinyan, Problem of choice and attractors in the processes of phase nucleation, competition, growth and ternary diffusion, Defect and Diffusion Forum. 143 (1997) 683-688.

Waryobab FAMU-FSU College of Engineering, Department of Mechanical Engineering, 2525 Pottsdamer St., Tallahassee, Fl 32310, USA a kalu@magnet.fsu.edu, bwaryoba@magnet.fsu.edu Keywords: OFHC Cu wire, Microstructure, Microtexture, Recrystallization, JMAK.
Kalu, In: Advances in Hot Deformation Textures and Microstructures (Ed.
Forum Vol. 408-412 (2002), p. 637

X-ray diffraction analysis was performed on a Bruker D8 ADVANCE ECO diffractometer in the Bragg-Brentano geometry under normal conditions in the emission of a copper anode (λ = 1.5418Å) using a Kβ - nickel filter.
Series: Materials Science and Engineering. 116 (2016) 012018
Series: Materials Science and Engineering. 177 (2017) 012134
Taube, Effect of the High-Heating on the Chemical and Phase Composition of the Al-Ni-Cr Layered Coatings, Materials Science Forum. 870 (2016) 169-174

Mridha1,b 1Advanced Materials and Surface Engineering Research Unit, Department of Manufacturing and Materials Engineering Research Unit International Islamic University of Malaysia, P.O.
A flat surface of the substrate was ground using emery paper and thoroughly cleaned before placing TiC particulates of nominal size 45 to 100 micron, 99.5% purity and supplied by Materion Advance Chemical.
Science Forum. 675-677 (2011) 783.

The Potential of the Mehedinţi County to Transform Waste into Resources Cristian Ghermec, Olimpia Ghermec University of Craiova, Faculty of Mechanics, Department of Engineering and Management of Technological Systems, Drobeta Turnu Severin, Romania cristian_ghermec@yahoo.com, olimpia_ghermec@yahoo.com Keywords: waste, resource, circular economy Abstract.
From the point of view of education in the field, in the Department of Engineering and Managenet of Technological Systems in Drobeta Turnu - Severin, University of Craiova is running the master program Environmental Management and Sustainable Energy (EMSE) which aims to develop competencies for the circular economy through disciplines such as: Sustainable industrial production, Life Cycle Assessments.
Bucşe, Studies on Integrated Waste Management in County Mehedinti, Advance in Engeneering Forum, Volume 27, 2016, pp.208-212 [10] EN ISO 16559 Solid biofuels – Terminology, definitions and descriptions [11] EN ISO 17225 Solid Biofuels - Fuel specifications and classes, parts 2 Graded wood pellets [12] http://www.paperforrecycling.eu/ [13] O.

Barbosa de Lima1,g 1Department of Mechanical Engineering, Federal University of Campina Grande, Zip Code 58429-900, Campina Grande, PB, Brazil 2Department of Petroleum Engineering, Federal University of Campina Grande, Campina Grande, Brazil 3Department of Agricultural Engineering, Federal University of Campina Grande (UFCG), Zip Code 58429-900, Campina Grande, PB, Brazil 4Department of Food Engineering, Federal University of Campina Grande (UFCG), Zip Code 58429-900, Campina Grande, PB, Brazil atrnporto@gmail.com, bantonio.gilson@ufcg.edu.br, cricardosoaresgomez@gmail.com, dtonyherbert@uapetro.ufcg.edu.br, egustavosantosdelima@gmail.com, fnubeniabiologia@gmail.com, gwan_magno@hotmail.com Keywords: Fluid flow, mathematical modelling, CFD, resin, composite.
The development of materials with specific properties is a relevant engineering topic.
Rethwisch, Materials Science and Engineering: An Introduction, octave ed., John Wiley & Sons, New Jersey, EUA, 2010
Vaidyac, Ballistic impact analysis of balsa core sandwich composites, Composites Part B: Engineering. 67 (2014) 160-169
Castilho, Thermomechanical Characterization of Hybrid Composites with Shape Memory, Dissertation (Master)-Mechanical Engineering, Brasília University, 2008.