Search results

Acknowledgement This research was supported by the key program of National Natural Science Foundation of China (NSFC 70931004).
Journal of Engineering Design.
Journal of Engineering Design.
Journal of Engineering Design.
Kim: Development of customer satisfaction models for automotive interior materials.

Information about safety valve including the material of the facture spring can’t be provided.
Therefore the spring material didn’t meet the requirement for spring steel.
Finally, improper material selection contributes to the failure.
Unsuitable material was also a reason for the failure. 4.
Journal of Yangzhou University(Natural Science Edition), Vol l3 No.( 2010), p.38-41(in Chinese)

High repetitive rate YAG laser pulse texturing, first developed by Institute of Mechanics, Chinese Academy of Sciences in 1992 [6-7].
Materials and methods Material.
Material component.
Etsion: Journal of Tribology, Vol. 127 (2005). p. 231-234
Neves et al.: Journal of Materials Processing Technology, Vol. 179 (2006), p.139-145

Introduction With the rapid development of science and technology, the requirements for material properties are becoming higher and higher, especially for materials working in a demanding environment where the material is often required to have high strength, good corrosion resistance and wear resistance, etc [1].
In this paper we studied the effects of gel casting process on the properties of materials [12].
Experimental Experimental raw materials.
(NH4)2S2O8,APS Beijing Chemical Reagent Factory Other raw materials used in this experiment are shown in Table 2.
Journal of Ceramic Society of Japan, 103, (1995)740-742

Christy1,b and Rein Terje Thorstensen3,c 1Department of Science, Faculty of Engineering and Science, University of Agder, Serviceboks 422, Kristiansand, Norway 2Department of Chemistry, Faculty of Science and Technology, Thammasat University, Khlong Luang, Pathumthani, 12120, Thailand 3Department of Engineering, Faculty of Engineering and Science, University of Agder, Serviceboks 422, Kristiansand, Norway asp.tanyapa@gmail.com, balfred.christy@uia.no, crein.t.thorstensen@uia.no Keywords: Near-infrared spectroscopy, calcium hydroxide, hydration, cement, concrete Abstract.
Kumar: Fourth International Conference on Sustainable Construction Materials and Technologies, SCMT4. (2016) [3] L.
Kumar: International Journal of Advanced Scientific and Technical Research, 6 (2013), 3, 151 [8] A.
Olmo: Materials, 6 (2013), 2508 [10] Y.
Sisomphon: The IES Journal Part A: Civil & Structural Engineering, 1 (2008), 2, 146 [12] T.

Value stream mapping was used to draw current state mapping with material flow, information flow, and time flow.
Process and material flow charts are drawn to demonstrate the operation details and complexity.
Future state map of product family AA Acknowledgements The research was supported by National Science Council of Taiwan, R.O.C.
International Journal of Production Economics, Vol. 107 (2007), pp. 223-236
Zammori: International Journal of Production Research, Vol. 44 (2006), pp. 3929-3952

China 2 Graduate University of the Chinese Academy of Sciences, Beijing 100049, P.
The layer would not deteriorate the material.
Stutzmann: Advanced Materials, vol. 18 (2006), p. 633 [4] T.
Hongbin:Journal of Semiconductors, vol. 33 (2012), p. 064007-1
Cao:Chinese Journal of Chemical Physics, vol. 26 (2013), p. 102.

As can be observed, a very large of work piece materials adhere at the corner of the edge, and tip at right-bottom of the cheisel edge, indicating that M2 uncoated drills are less resistant to the adhesion of work piece materials in dry cutting conditions. 1 2 1 2 The morphologies of the chesal edge surface of MoS2/Zr coated drills after drilled 32 holes are shown in Fig. 6.
[3] N.Renevier,V.Fox,D.Teer et al:Materials & Design,Vol.21(2000), pp.337-343
[5] J.Lince,M.Hilton,A.Bommannava:Journal of Materials Research,Vol.10(1995),pp.2091-2105
[9] W.Kao,Y.Su:Material Science Enginerring A:Vol.368(2004), pp.239-248
[17] W.Oliver,G.Pharr:Journal of Materials Research,Vol.7(1992),pp.1564-1583.

Traditionally, kenaf bast fibers are used to rope, twine and course sacking materials.
Materials and Methods.
Materials.
International Journal of Basic and Applied Sciences 10(3): 54-57
Journal of Composite Materials 44, 2265–2288

German and Bose [7] reported that the binder portion in the injection molded metallic materials is usually about 30 %; whereas it reaches 50 % or more in the ceramic materials.
Khalil, Effect of Powder Loading on Metal Injection Molding Stainless Steel, Journal of Materials Processing Technology 183 (2007) 432-439
Khor, S.B Tor, Mixing and Characterization of Feedstock for Powder Injection Molding, Materials Letters 46 (2000) 109-114
Levenfeld, Development of a Feedstock Formulation Based on PP for MIM of Carbides Reinforced M2, Journal of Achievement in Materials and Manufacturing Engineering 27(2) (2008) 195-198
Maeda, Mixing and Characterization of 316L Stainless Steel Feedstock for Micro Powder Injection Molding, Materials Characterization 54 (2005) 230-238