Search results

However, to machine of isotropic pyrolytic graphite is very difficult due to the highly abrasive nature of graphite materials.
It not only had a close relationship with the properties of the work-piece materials, but also with the cutting model and cutting parameters [4-6].
Grácio : Diamond & Related Materials 15 (2006) 1753-1758 [2] S.
Lu : Journal of Yanshan University 30 (2006) 403-406 (Chinese) [3] M.
Liu, Journal of Materials Processing Technology 185 (2007) 24-30 [7] Zhou Li: Research on High speed Milling of the High-performance graphite

Materials and Methodology In this study, secondary data of the Statistical Office of the Slovak Republic, Ministry of Interior Affairs of the Slovak and the Slovak Road Administration were used.
Levinson, Gasoline prices and traffic safety in Mississippi, Journal of Safety Research. 41 (2010) 493–500
Levinson, Gasoline price effects on traffic safety in urban and rural areas: Evidence from Minnesota 1998–2007, Safety Science. 59 (2013) 154–162
Levinson, The impact of gasoline price changes on traffic safety: a time geography explanation, Journal of Transport Geography. 28 (2013) 1–11
Dee, Motorcycle helmets and traffic safety, Journal of Health Economics. 28 (2009) 398–412

K-values, derived from numerical simulation, for different materials were virtually equivalent for the 12 mm bend radius.
The differences between different materials found in the experimental study could not be detected.
In comparison, bend angle and materials investigated here only have little effect on the initial sheet width.
J. de Vin, Expecting the unexpected, a must for accurate brakeforming, Journal of Materials Processing Technology. 117 (2001) 244-248
Altan, Prediction of bend allowance and springback in air bending, Journal of manufacturing science and engineering. 129 (2007) 342-351

Rimshin, The Limiting Values of Moments And Deformations Ratio in Strength Calculations Using Specified Material Diagrams, IOP Conference Series: Materials Science and Engineering. 463(3), 032024 (2018)
Rimshin, Technical aspects of using composite materials for strengthening constructions, IOP Conference Series: Materials Science and Engineering. 365(3), 032053 (2018)
Tverskoi, Durability of Buildings in Urban Environment, Materials Science Forum. 931, 340-345 (2018)
Davydova, Building Model of Behaviour of Concrete under Load, IOP Conference Series: Materials Science and Engineering. 661(1),012074 (2019)
Astafeva, Deformability of a Volume-Compressed Concrete, IOP Conference Series: Materials Science and Engineering. 463(2), 022063 (2018)

In this research, materials used as the main raw material were silver nitrate (AgNO3).
Nanowires are 1D nanostructured materials with diameters between 10 and 200 nm and lengths between 5 and 100 µm [4-8].
The synthesis of NWs continues to be of interest to researchers and the development of materials for the synthesis of NWs from various types of metals.
Materials and Methods The materials used for synthesizing of AgNWs through polyol method included silver nitrate (AgNO3, 99%, Merck), polyvinyl pyrrolidone (PVP), Sigma-Aldrich, Mw. 55000 g/mol), ethylene glycol (EG, 99%, Merck), propylene glycol (PG, 99%, Merck), and Iron(III) chloride (FeCl3.6H2O, Sigma Aldrich), ethanol (EtOH, 98%, Merck).
Son, Effects of synthesis conditions on the formation and morphology of silver nanowires, Vietnam Journal of Science & Technology 56 (2018) 111–117, https://doi.org/10.15625/2525-2518/56/2A/12637

Bamboo fiber reinforced resin matrix brake materials were selected as research object, dry and wet friction experiment was conducted on MM200 abrasion tester.
Wear and corrosion of friction materials is either accompanied by mechanical broken of wear debris, or due to the collapse of the patches.
Water cooling will reduce the adhesion transfer of the materials between the friction pairs, so the friction coefficient and wear rate is lower than dry friction[9].
Liew.: Journal of materials processing technology 208 (2008) 135-144
Singh: Materials and Design 31 (2010) 2745–2751

Xue: Key Engineering Materials, Vol. 419-420 (2010), p. 253 [3] Y.H.
Du: Advanced Materials Research, Vol. 97-101(2010), p. 642 [5] Y.
Peng: Transactions of Materials and Heat Treatment, Vol. 22, n 4(2001), p. 25 [6] Y.
Ishihara: Journal of Materials Science and Technology, Vol. 24, n 1(2008), p. 41 [7] Z.H.
Tao: Journal of Aeronautical Materials, Vol. 29, n 6(2009), p. 59 [8] E.

Reconstruction of administrative buildings of the 70's: The possibility of energy modernization (2014) Journal of Applied Engineering Science, Volume 12, Issue 1, pp. 37-44
The energy-efficient heat insulation thickness for systems of hinged ventilated facades (2014) Advanced Materials Research Vols. 941-944, pp. 905-920
Increase of energy efficiency of the building of kindergarten. (2014) Advanced Materials Research, Vols. 953-954, pp. 1537-1544
Increase of energy efficiency for educational institution building. (2014) Advanced Materials Research, Vols. 953-954, pp. 854-870
Comprehensive method of energy efficiency of residential house. (2014) Advanced Materials Research.

Fabrication of self-healing ceramic coating against oxidation for carbon/carbon composite using polysilazane and fillers Liu Hongli a*, Tian Chunying b College of Materials Science and Engineering, Jiamusi University, Jiamusi 154007, China a *corresponding author, email: lhl@mse.buaa.edu.cn b email: tcywkx@126.com Keywords: Preceramic polymer, Anti oxidation coating, C/C composite, Fillers Abstract.
A number of techniques such as chemical vapor deposition (CVD), pack cementation, evaporation, sputtering, and plasma spraying have been used to provide coatings for C/C composites with oxidation-resistant materials[2,3].
However, in spite of its advantage, work reported on the coating of C/C composites with different oxidation-resistant materials using this technique is quite scanty.
Schwarz: Journal of Nuclear Materials Vol. 367 (2007), p. 1139 [3] H.
Chen: Rare Metal Materials and Engineering Vol.35 No.1 (2006), p.134

According to the included in the financial method, project cost can be divided into direct and indirect expenses, and direct expenses include labor, materials, machinery fee.
The decision-making model According to the above, building project costs include four components, namely materials costs, labor costs, machine costs, and CO2 emission costs.
Supposed these five projects consume the same materials.
The vendor of materials provides a discount of 10% if the quantity of purchase exceeds 10,000,000.
T: Journal of Environmental Planning and Management, 56(7): 934–952(2013)