Search results

However, to machine of isotropic pyrolytic graphite is very difficult due to the highly abrasive nature of graphite materials.
It not only had a close relationship with the properties of the work-piece materials, but also with the cutting model and cutting parameters [4-6].
Grácio : Diamond & Related Materials 15 (2006) 1753-1758 [2] S.
Lu : Journal of Yanshan University 30 (2006) 403-406 (Chinese) [3] M.
Liu, Journal of Materials Processing Technology 185 (2007) 24-30 [7] Zhou Li: Research on High speed Milling of the High-performance graphite

I wish your journal could be kind to review this paper of mine.
The cost of production, the material, grinding wheel and the machine time are much higher than my method.
Journal of Machine tool and manufactureing.Vol.,17(1998),p.39 [4] Liu Huran, The cutting edge of the rotary tool with complex surface.
Journal of Cutting Tool,Vol.19 (1994),p.47 [5] Zhou Ji, The moldering and design of the transitional cutting edges.
Journal of Chinese Mechanical Engineering Vol.25(2003),p.18

Acknowledgements This work was financially supported by the Ministry of Housing and Urban-Rural Development Soft Science Research Foundation (2012-R3-7).
References [1] Information on http://www.law110.com/lawserve/guihua/1800039.htm [2] Yin Zhang, Bo Wang and Jian Zhang: submitted to Journal of Xi’an University of Architecture and Technology (2011)
[3] TengFei Lin and ZhouDu Hou: submitted to Journal of Xi’an University of Architecture and Technology (2003)
[4] Dorota Kuchta: submitted to International Journal of project management(2001)
[6] JiJun Zhang submitted to Journal of Fuzzy Systems and Mathematics (2000).

The most typical interference: global interference-cutting tools collide the other parts of surface when tools processing surface; local interference work piece materials are over-cutting or under-cut.
Fig.8 Ball-end cutter processing free surface simulation process Fig.9 Actual processing Acknowledgements This thesis is supported by the Fund of AVIC Aeronautics Science and the State Key Laboratory Foundation of Educational Department of Liaoning Province.
Liu: Chinese Journal of Mechanical Engineerin, Vol. 42, No. 6, (2006), p. 177 [6] J.
Liang, Journal of South China University of Technology Vol. 30 No. 4 (2002), p. 27 [7] X.
Zhao: Journal of Mechanical Engineering Vol. 46 No. 17 (2010), p. 140 [8] Juttler B and Wagner M G: Journal of Mechanical Design Vol. 119, No. 2 (1996), p. 193 [9] C.

The Experimental Study on Creep and Shrinkage of  High Strength Concrete with Fly Ash Jian-qun Wang 1, a, Zhi Fang 2,b and Zhijian Tang 3,c 1 Department of Civil Engineering, Hunan Univ of Science & Technology, Xiangtan, Hunan, China 2 Department of Civil Engineering, Hunan Univ, Changsha, Hunan, China 3Guangxi Airport Management Group Co.
ACI Materials Journal,2001,98(2): 159-167
Journal of the American Concrete Institute,1979,76(3):387-403
Journal of The American Concrete Lnstitute, 1976.73(8):469-472
Journal of The American Concrete Institute,1981,78(5):351-357

Materials adopted in the design were Q235B low-carbon steel for steel members and C20 concrete for floor slab.
Acknowledgements This work was financially supported by Ministry of Science and Technology of China (2004EG131165).
Goel, “Dynamic analysis of staggered truss framing system” Journal of the Structural Division, 1972, 98(7), 1475-1492
Itani, “Seismic behavior of open-web truss-moment frames”, Journal of Structural Engineering, 1994, 120(6), 1763-1780
Itani, “Seismic-resistant special truss-moment frames”, Journal of Structural Engineering, 1994, 120(6), 1781-1797

Acknowledgement It is a project supported by the International Science & Technology Cooperation Program of China, （No. 2011DFB60150）.
[2] Rui Quan, Shuhai Quan, Liang Huang et al: Journal of Shanghai Jiaotong University, Vol. 45(2011), p. 842-846+850, in Chinese
Musa: International Journal of Automotive Technology, Vol. 1(2008), p. 30-34
[4] Yadong Deng, Tao Fan, Xun Guo et al: Journal of Wuhan University of Technology(Information & Management Engineering), Vol. 32(2010), p. 265-267, in Chinese
Engström: Journal of Fluids Engineering, Vol. 126(2004), p. 791-798.

International Journal of Information Technology,2005,11(1):16-24
Journal of Shandong University(Natural Science).2010.Vol 45,No 5.48-52
International Journal of Information Technology, 2005, 11(1): 16-24
International Journal of Machine Tools and Manufacture, 2004, 44(10): 1077-1084
Sensors and Materials, 2013, 25(1): 1-15

Zhao: Journal of Building Structures Vol. 16(1995), p. 37-43
Yu: Journal of Building Structures Vol. 30 (2009), p. 27-35
Ding: Journal of Building Structures Vol. 22 (2001), p. 2-7
Wang: New Building Materials (2007), p. 57-59
Yang: Journal of Chongqing Jianzhu University Vol. 30 (2008), p. 5-8

Experimental study and the theoretical model of optical flowmeter of solid debris. chinese journal of mechanical engineering, 2004, 40(8):160-165
Chinese Journal of Scientific Instrument, 2013,34(4):762-767 [4] X.
Journal of Nanomaterials, 2014, 2014
Study on the resolution-frequency characteristic of microfluidic oil detection chip, Chinese Journal of Scientific Instrument. 2014,35(2),427-433 [6] H.
Applied Mechanics and Materials, 2012, 117: 517-520