Search results

Utilization of Waste Printed Circuit Board Resin in Controlled Low-Strength Materials Ing-Jia Chiou1,a, Chu-Chan Chiang2,b, Cheng-Lan Ho2,b 1 Graduate School of Materials Applied Technology, Taoyuan Innovation Institute of Technology, No. 414, Sec.3, Jhongshan E.
Adaska, Controlled Low-Strength Materials.
Rafat, Utilization of waste materials and by-products in producing controlled low-strength materials, Resources, Conservation and Recycling, Vol. 54 (2009), p.1-8
Rosell, Combined use of MSWI bottom ash and fly ash as aggregate in concrete formulation: Environmental and mechanical considerations, Journal of Hazardous Materials, Vol. 169 (2009), p.643-650
Siti, Performance appraisal of industrial waste incineration bottom ash as controlled low-strength material, Journal of Hazardous Materials, Vol. 172 (2009), p.862-867

Metal additive manufacturing: a review, Journal of Materials Engineering and Performance. 23(6) (2014) 1917-1928
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges, Composites Part B: Engineering. 143 (2018) 172-196
Additive technology for manufacturing structurally-graded materials from the Inconel 625 nickel-based superalloy, IOP Conference Series: Earth and Environmental Science. – IOP Publishing, 194(4) (2018) С. 042013 [18] Bax B. et al.
Experimental Study on Laser Metal Deposition of FGMs with Ultrasonic Vibration, Applied Mechanics and Materials, Trans Tech Publications, 271 (2013) 131-135
Study of Ti64 vibration laser metal deposition process, Advanced Materials Research. – Trans Tech Publications, 189 (2011) 512-517.

In IOP Conference Series: Materials Science and Engineering (Vol. 523, No. 1, p. 012080).
In IOP Conference Series: Materials Science and Engineering (Vol. 352, No. 1, p. 012020).
Journal of Sustainable Materials, 25(3), 175-192 [7] Tamlicha, A., Rizal, S., Hasanuddin, I., Pahlevi, A., Nazaruddin, Noor, M.
International Journal of Materials Research, 41(3), 789-803
Journal of Advanced Materials, 52(1), 45-60

Hill, Nanoarchitectonics for Mesoporous Materials.
Journal of Materials, (2014), 1–9. doi:10.1155/2014/184216 [12] E.O.
Journal of Hazardous Materials, 290 (2015), 117–126. doi:10.1016/j.jhazmat.2015.02.061  [18] A.
Journal of Colloid and Interface Science, 277(2), 316 326. doi:10.1016/j.jcis.2004.04.051 [23] E.E.
Advanced Materials Research, 626, (2012), 997–1000

Laser assisted turning is an effective method machining difficult-to-machine materials such as ceramics, which uses a high power laser to focally heat a workpiece prior to material removal with a traditional cutting tool.
[3] Tian Y and Shin Y C: Journal of Manufacturing Science and Engineering Vol.128 (2006) No.2, p. 425-434
[4] Ho C Y, Wen M Y and Ho J E: Journal of Materials Processing Technology Vol.192-193(2007), p. 525-531
[6] Tian Y and Shin Y C: Journal of Manufacturing Science and Engineering Vol.129 (2007) No.2, p. 287-295
[10] Rebro P A, Shin Y C and Incropera F P: Journal of Manufacturing Science and Engineering Vol.124 (2002) No.4, p.875-885

Experiments Materials.
The materials were purchased from Innovative Pultrusion Sdn Bhd.
Materials were weighed according to the formulation in Table 1.
Advances in Materials Science and Engineering, 2013: p. 14
Journal of materials science, 2011. 46(18): p. 6075-6086

As shown from Fig. 4 and Fig. 5, improving the strength grade of structural elements materials can achieve the goal of increasing the bearing capacity of them.
Compared with that under room temperature, the strength reduction of the materials affected by high temperature has already reduced the bearing capacity.
As a result, in the process of construction and materials selection, importance should be attached to choosing over tensioning or low relaxation cables.
[2] Y.Du and Y.Z.Lu: Journal of Disaster Prevention and Mitigation Engineering, Nanjing, Vol.32 (2012) No.5, pp.72-76, in Chinese
[6] X.J.Ren: Journal of Anhui Institute of Architecture & Industry (Natural Science), Vol.15 (2007) No. 6, pp.16-18, in Chinese

Brouwer, Microstructure characterisation and mechanical properties of ODS Eurofersteel subject to designed heat treatments, Materials Science & Engineering, Page-138568, (2020)
[4] AtanuSaha, Dipak Kumar Mondalb,Effect of cyclic heat treatment on microstructure and mechanical properties o 0.6 wt% carbon steel, Materials Science and Engineering, Pages- 4001–4007, (2010)
Gammer, Effect of heat treatment on microstructure and mechanical properties of 316L steel synthesized by selective laser melting, Materials Science & Engineering, Pages-205–212, (2019)
[11] HanlinPeng, Ling Hu, Effects of austenitizing temperature on microstructure and mechanical property of a 4-GPa-grade PM high-speed steel, Materials Science & Engineering, Pages-21-26, (2018)
Saber, Mechanical and microstructure characteristics of heat-treated of high-Cr WI and AISI4140 steel bimetal beams, Journal of materials research and technology, Pages-7926-7936, (2020).

With recent developments in technology and science, we have been depending heavily on synthetic materials for various applications.
Experimental Materials.
Journal of Polymer and Environment. 18 (2010) 65–70
Influence of tool materials on thrust force and delamination in drilling sisal-glass fiber reinforced polymer (S-GFRP) composites, Procedia Materials Science 5(2014) 1915–1921
Surface roughness optimization of machining parameters in machining of composite materials, International Journal of Applied Research in Mechanical Engineering 1(1) (2011) 26-32

Some traditional shipyard switch to using FRP materials to be able to keep the activity of building fishing boats.
Nevertheless FRP materials have not been fully accepted by the most of Indonesian fishermen.
One alternative composite materials that meet innovation is laminated bamboo slats.
In: Proc. 18th International Conference on Composites Materials, ICCM 2011, Jeju, Republic of Korea (2011)
Talabgaew, Experimental Studies on the Mechanical Property of Laminated Bamboo in Thailand, International Journal of Engineering and Applied Sciences (2007)