Search results

"Green technology" has become the 21st century hot cross-development research and cutting-edge technology between the fields of energy conservation and environmental protection and other areas of science and technology [2].
Recently, supercritical CO2 extraction technology as a common technology, and gradually penetrate into the textile dyeing, environmental pollution control, new materials and other high-tech fields, is considered a "green, sustainable development technology" has become widely accepted.
Materials and methods Materials.
Dyeing and Finishing, Vol.1 (2009),p.44 [2] Chuanhua Liao,Benyin Chai: Supercritical Fluid and Preparation of New Materials ,edtied by China Petrochemical Press,2007 [3] Ping Bao, Jinjin Dai: J.
Journal of Supercritical Fluids, Vol.30 (2004),p.42 [5] Tachyoung Kim, Gwansoo Kim, Ji-Yong Park: J.

The meshing number is set for 41851, the material of the impeller is structural steel, which material properties shown in Table 3.
So, in here, it can adopt the greater strength stainless steel material as the impeller blade.
Acknowledgements The project is supported by the Science Fund of Jiangxi Province No. 20131512040282.
Advanced Materials Research.
Modeling and Control of Oxygen Transfer in High Purity Oxygen Activated Sludge Process, Journal of Environmental Engineering. 3, (2003), pp402-411.

Introduction In the recent decade a heightened interest is observed to the study of the weak magnetic field influence on the characteristics and properties of various materials.
To clarify the role of Ni in MPE-formation during the ageing process of Cu-Be-alloys out of high-clean certificated materials, special models of triple Cu-Be-alloys with Ni-additives of 0.4 and 1.0 wt
This is of a high practical importance for producing of nano-materials with pre-specified properties.
Natural-science series 78 (2010) 145 (in Russian)
Buchachenko: Journal of experimental and theoretical physics: Vol. 109 (2009) 434

Magnesium alloys are widely used as structural materials.
The heat-resistance of Mg alloy is always focused by material academic circles.
The ingots were cast by steel mould; the raw materials to produce the alloys are magnesium (99.9% mass pct) ingots, aluminum (99.9% mass pct) ingots, Mg-Y master alloy ingots and Mg-Nd master alloy ingots.
International Materials Review, 2004, 49(2): 13-29
Journal of Southeast University: Nature Science, 2005, 35(2): 261-265

It is believed that we will achieve the clear teaching objectives, teaching content optimization, teaching structure science, practice and reasonable three-dimensional construction of teaching materials, stability of the faculty, teaching and curriculum goals with rich research fruits.
While allowing students to exchange experiences in cooperative learning, the combination of "doing science".
Liaoning Teachers College (Natural Science), 2008 (4)
University of Petroleum: Social Sciences, 2003,19 (1) :110-112
Journal of Southwest Agricultural Admission: Social Science, 2005, 3 (4) :192-194

At present, the representation and reasoning mode of visual imagery has gradually become one of the hot topics in the field of scientific and technological research, and it has attracted wide attention from experts of cognitive psychology, cognitive neuroscience, cognitive science and computer science[1].
Acknowledgements Our work is supported by project of science and technology development of Jilin provincial education department, China (No. 2012402).
Liu: Journal of Bionic Engineering, vol. 7(2010), p. 238
Wang: Science in China.
Zhang: Advanced Materials Research.

The operating conditions of the diaphragms impose special requirements on the structural materials for their manufacture.
Materials and Methods Determination of the hyperelastic material model based on numerical and experimental studies.
Journal of applied physics, 11(9):582‐592, (1940)
Saunders, Large elastic deformations of isotropic materials. vii. experiments on the deformation of rubber.
Kalgankov, Determination of the durability of elastic hereditary materials using generalized failure criteria, Vost.

-joo Na: Journal of Manufacturing Processes.
-joo Na: Journal of Manufacturing Systems.
Toyosada: Journal of Marine Science and Technology.
Wright: Journal of Manufacturing Systems.
Dorigo: INFORMS Journal on Computing (2000)

Experimental Thermal and Fluid Science, 62, 2015, p. 151-163, DOI: 10.1016/j.expthermflusci.2014.12.014 [4] Hunicz J., Gęca M.
Journal of Vibroengineering, 2013, Vol. 15(3), p. 1093-1101
Journal of KONES, 19(3) 2012, p. 9-18
Journal of KONES, 18(4), 2011, p. 389-396
Mechatronic Systems, Mechanics and Materials II, Vol. 210 (2014), p. 136-141.

Journal of Computer-Aided Design & Computer Graphics, 2001,13(06)：570-575(in chinese)
Indian Institute of Science, 2005, 85, 161–182
Journal of Computer-Aided Design & Computer Graphics, 2001, 13 (7): 631-635
Advanced Materials Research Vols. 139-141 (2010) pp 1322-1327
journal of shanghai jiaotong university, 1991, 10 (in Chinese)