Search results

Engineering in seawater face materials corrosion such as concrete and steel bars attacked.
A range of supplementary cementing materials (SMC’s) exist including GGBS (ground granulated blast furnace slag), PFA (pulverised fuel ash) and other waste materials from industrial processes [10].
The raw materials are extracted from the quarry crushed to a very fine powder and then blended to the correct proportions [11, 12].
Because CaCl2 and Mg(OH)2 are non-gelation materials they seriously damaged the inner structure of concrete, at the same time many free chloride ions lead to the corrosion of steel.
United States of America, American Society for Testing and Materials

Product Information Model of MEMS Xiangtong Yan School of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China yenxt@sina.com Key words: MEMS; XML; Information Representation; Information Exchange Abstract.
Representation of Material Information The MEMS material attribute data has the obvious half structurized characteristic.
Moreover, non-silicon materials such as glass, quartz, ceramic, plastic and metal material are also emerging in MEMS.
The commonly used materials and the attributes in the MEMS design and manufacturing are described using XML in this section.
Journal of Wuhan University of Technology.

Introduction Lead titanate(PT) as a typical perovskite-type ferroelectric materials, has been extensively studied due to its remarkable ferroelectric, pyroelectric and piezoelectric properties and applied as high frequency piezoelectric materials such as optoelectronics, transducers, sensors and nonvolatile memories in advanced technology fields[1,2].
The research work provides the probability of the application of such materials and aid in the research work of preparation of relative films.
Materials exhibit apparent piezoelectric effect with enlarged activity of atoms in c axis and anisotropic characteristics.
Additional, the little changing of δof PMT in 0.1~1MHz aid in the development of its applications as excellent piezoelectric materials.
It is believed that the extent of single-domainization has a sever influence on the pyroelectric performance of the materials.

Experimental Materials.
Seal, Graphene based materials: Past, present and future.
Progress in Materials Science. 56(8) (2011) 1178-1271
Wilson, Encyclopedia of Materials Characterization: Surfaces, Interfaces, Thin Films. 1992: Butterworth-Heinemann
[12] Sibilia, J.P., A Guide to Materials Characterization and Chemical Analysis. 1996: Wiley

Introduction The ferritic stainless steels are materials of great interest in diverse areas because of their excellent combination of mechanical properties and corrosion resistance.
The crystallographic textures in the starting materials were determined by means of X-ray diffraction using a Philips X’Pert PRO MPD texture diffractometer.
ENGLER, MATERIALS SCIENCE AND ENGINEERING A. 308 (2001) 74-78
Xin, Journal of Iron and Steel Research. 17 (2010) 47-52
Takemoto, Materials Transactions. 47(2006)1769-1775.

Journal Citation (to be inserted by the publisher ) Copyright by Trans Tech Publications HYDROTHERMAL CONVERSION AND SOL-GEL COATING OF RED SEA CORAL J.K.
Ben-Nissan,1 1 Department of Chemistry, Materials and Forensic Science University of Technology, Sydney PO Box 123, Broadway, NSW, 2007 Australia 2 Institute for Applied Biosciences, and Department of Biotechnology Engineering, Ben-Gurion University of the Negev, Beer Sheva 84105 Israel Joanna.K.Innes@uts.edu.au Keywords: coral, hydrothermal, hydroxyapatite, sol-gel.
Materials and Methods This current patented technique, involves two-stage application route.
This offers a material with a high similarity to the structure of natural bone.
Ben-Nissan, , " 31P Solution State NMR Investigation of the Hydrolysis of a New Alkoxide Sol-Gel Hydroxyapatite", Bioceramics Volume 14, Trans Tech Publications, Key Engineering Materials, (Eds.)

(2) Screw φ32 mm, trapezoidal thread, the pitch diameter φ29 mm, and screw pitch 6 mm, material 40 Cr with a length of 1000 mm
(5) Road wheel is directional wheel with universal casters, model (series 4 - flat type - activity type), wheel diameter φ125 mm, number: 4404761, materials for super polyurethane (black), wheel width 50 mm, bearing 420 kg, installation height 350 mm with quality 2.29 kg [4].
:L2012232), and the Twelfth Five-Year Rural Areas National Science and Technology Plan subject (grant No.:2011BAD20B09-10).
Material mechanics (4th Edition) [K] Beijing: Higher Education Press, 2004
Journal of Shenyang Engineering College, 2010, 6 (3):271-273

It will be even resulfurization phenomena for the raw materials [2~4].
The iron materials would increase and the smelting state was also much bad.
Table 1 The mass fraction of material components ( % ) Material CaO MgO SiO2 S Lime 87.15 6.4 1.29 0.040 dolomite 47.89 34.57 1.76 0.040 Ore — — 3.62 0.030 We sampled in each process and obtained the proportion of sulfur from various raw material by analyzing the sulfur content of the materials and calculating the material balance, which was shown in Fig. 4.
Acknowledgements This work was financially supported by National Natural Science Foundation of China (50974051).
Journal of Iron and Steel Research, 2011, 23(12): 20~21.

Introduction Any producer consumes resources (human, financial, material, etc.) and uses several techniques (technological) to obtain one or more results (outputs).
Acknowledgements: This paper was supported by the project "Doctoral studies in engineering sciences for developing the knowledge based society-SIDOC” contract no.
Ray, Measuring and Decomposing Sources of Productivity Performance in India’s Paper and Pulp Industry under Liberalized Regime: A Nonparametric Approach, International Journal of Economic Sciences and Applied Research, Vol. 5, No. 1 (2012) pp. 147-171
Diewert, Multilateral comparisons of output, input, and productivity using superlative index numbers, The Economic Journal, Vol. 92, No. 365 (1982) pp. 73-86
Yen, Evaluation of human resources in science and technology by using dynamic Malmquist index approach and window analysis, African Journal of Business Management, Vol. 6, No. 14 (2012) pp. 5004-5013

And still again it is necessary to return to the questions of the choice and application of hardening environments, but already in terms of the maximum realization of the properties put directly in the material of product.
Gedberg, Use of the «TOSOL-K » quenching fluid for the bulk quenching of steels, Metal Science and Heat Treatment, Moscow, 24(5-6) (1982) 377-380
Shveyov, Surface Layer Metal Diagnosis of Carburized Parts, World Applied Sciences Journal 29(12) (2014) 1566-1568
Shveyova, Forecasting of Carburized Tooth Parts Durability on Metal of a Core Properties, World Applied Sciences Journal 29(12) (2014) 1550-1552
Karginova, Blotchy carburization of steel, Metal Science and Heat Treatment, Moscow, 1982, [22] V.