Search results

The materials used for a production of composite material are glass fibre tex4800 with fibre mass fraction of 53  and vinyl ester resin CRYSTIC VE 676-03.
Series: Materials Science and Engineering. 96 (2015) 012012 10 p
Graf, Numerical simulation of advanced pultrusion processes with microwave heating, In: Proceedings of the VII European Congress on Computational Methods in Applied Sciences and Engineering.
Watson, Weight optimal design of lateral wing upper covers made of composite materials, Eng.
Series: Journal of Physics: Conf.

According to the geological profile(as shown in Fig.2.1below) model is divided into strongly weathered (deformation), Strongly unloading, weak unloading, weak weathered, slightly weathered and micro new six kind of materials(as the following table 1shown) to established.
Model materials zoning maps before and after excavation of the spillway tunnel are shown as the following Fig.2.3 and Fig.2.4: Fig.2.1 Geological section map Tab.1 Slope mechanics parameter table Material Name Modulus of elasticity Poisson's ratio u Cohesion C Angle of internal friction Density （g/cm） （GPa） （MPa） Φ(。)
Acknowledgements This work was financially support by National Natural Science Foundation of China (No: 50909052), Key Project of Ministry of Education of China (No: 212114).
Slope engineering[M].Beijing: Science Press,2010
CHINESE JOURNAL OF ROCK MECHANICS AND ENGINEERING,2000(4) [5]Jia Shanpo,Chen Weizhong,Yang Jianping,Chen Peishuai.

Mechanical Engineering, Applied University of Berlin HTW, Berlin, Germany 2Federal Institute of Materials Research and Testing BAM, Berlin, Germany amarcus.wolf@bam.de, banja.pfennig@htw-berlin.de Keywords: duplex steel, crack growth, corrosion fatigue, electrochemical potential.
During corrosion fatigue, crack propagation in materials occurs as a coupled process of mechanical loading and corrosive environmental interaction, leading to accelerated crack growth compared to purely mechanical fatigue.
Wolf.: Journal of Physics: Conf.
Simkin: Applied Sciences 15(1) (2025) 403 [15] M.
Pfennig: 8th International Conference on Materials Sciences and Nanomaterials (ICMSN 2024), 9.-12.7.2024 Edingburgh, Great Britain [16] M.

The results show that there is material transfer due to arc erosion while breaking arc and closing bounce.
Therefore, easing the arc erosion and decreasing the material transfer is necessary for increasing the life of relay.
Acknowledgements This work was financially supported by the National Natural Science Foundation of China (51177021).
Effect of voltage and contact materials on breaking duration of relays.
Journal of Zhejiang University( Engineering Science), 2006,03:448-453

Materials and Methods The chicken ESW was used as raw material collected from Kafe Hanain in Parit Raja, Johor, Malaysia.
XRD analysis was conducted to analyse the phase existence of materials in range between 10 o to 70o for 2θ.
Metals, Materials and Minerals, 28 (2018) 124–135
Medical, A preliminary study of extraction of sulphur and calcium from eggshell waste, International Journal of Current Research, 11 (2019) 1547-1549
Rodrıguez, Synthesis of hydroxyapatite from eggshells, Materials Letters, 41 (1999) 128–134

Introduction Currently, steel fiber concrete is given special attention as one of the fastest growing effective and promising building materials.
It can be seen that the higher the heating temperature, the greater the relative decrease in the mass of materials.
The results of the effect of heat has on the linear dimensions of the material samples are given in (Fig. 2).
Moreover, after 800 and 1000 ° C in materials with a volumetric fiber content of 3% and 6% when using certain types of fiber, an increase in size occurs. 2.
Ivanenko, Results of verification of the model of fiber concrete structure developed for analytical determination of its thermal and radiation changes based on experimental data of shrinkage during hardening, Internet-journal "science of SCIENCE" That. 8, 4 (2016). http://naukovedenie.ru/PDF/43TVN416.pdf.

The Contact Simulation of CTP Imaging Drum and Plate on ANSYS XING Jie-fanga, ZHANG Jieb, HE Lu-junc Jiangsu Provincial Key Lab of Pulp and Paper Science and Technology, Nanjing Forestry University, No.159 Longpan Road, Nanjing, Jiangsu China, 210037 ajfx200@yahoo.com.cn, bzjahfy236400@126.com, chelujun8853@yahoo.cn Key words：ANSYS；contact process；imaging drum；finite element Abstract.
As the changing of load material boundary conditions and other factors, one surface may contact or not contact with other surfaces in a sudden which will cause abrupt change of system rigidity; contact problem often involves in the solving of friction response, and the result is difficult to converge.
In rigid - flexible body contact problems, one or more contact surfaces are taken as a rigid body (with a much larger rigidity than the other contact surface), which is suitable for the case that soft materials contacts with hard materials; flexible - flexible body contact is suitable for the two contact deformable bodies with similar contact rigidity, which is the most common type.
Advance Materials Research(First International Conference on High Performance Structures and Materials Engineering (ICHPSM2011)), beijing,2011,217-218: 1781-1788
Defence Science Journal, Vol.57, No.2, March 2007, 57(2):165-171

Materials and Experimental details Concrete materials.
Kiattikomol, Construction and Building Materials, 21 (2007) 1589-1598
Hashim, Construction and Building Materials, 24 (2010) 1590-1593
Kiattikomol, Journal of materials in civil engineering, 21 (2009) 426
Ariffin, Construction and Building Materials, 30 (2012) 281-288

So the choice of materials is particular important in green ship design process [7].
During production design, consideration should be focused on the pollution problems of welding materials on environment in the welding process.
Efficient, low toxic and low smoke welding materials are preferred materials.
So when choosing ship outfitting materials, not only the general function must be consider, but also the environmental performance must be considered too.
[7] Zhengping Zhao: Journal of Marine Technology Vol. 5(2003), p. 5-8, in Chinese

Microstructure, tensile property and wear property of the sintered materials were investigated. 2.
The nominal compositions of the experimental materials are summarized as given in Table 1.
Acknowledgements The authors are grateful for financial and technical supports from Thailand Graduate Institute of Science and Technology: TGIST (TG-33-26-59-045M), Thailand National Metal and Materials Technology Center (MTEC) and Naresuan University are acknowledged for the financial support.
Tongsri, Iron-carbide composites prepared by P/M, The Minerals, Metals and Materials Society-3rd International Conference on Processing Materials for Properties 2008, PMP III, 1, pp. 571-578
Vetayanugul, Thermal analysis of Fe-Carbide and Fe-C mixtures, Journal of Metals, Materials and Minerals 20 (2010) 45-49