Search results

Composites Science and Technology.
Composites Science and Technology.
Composites Part A-Applied Science and Manufacturing.
Journal of Composite Materials.

Journal of Scientific Exploration, 1983, (1): 83-97
Beijing: Science Press, 2007
Chinese Science Bulletin, 1999, 44(17): 1538-1548 [8] An C.H., Hollerbach J.M., The Role of Dynamic Models in Cartesian Force Control of Manipulators, The International Journal of Robotics Research,Vol.8,No.4, August 1989,pg. 51-71 [9] Fisher W.D., Mujtaba M.S. - Hybrid Position/Force Control: A Correct Formulation, The International Journal of Robotics Research, Vol. 11, No. 4, August 1992, pp. 299-311
Journal Of Harbin Institute Of Technology, 2006, 38(7): 1146-1149
Engineering Science, 2001, 3 (7): 54-58

With the method, the drill bit performance could be predict analyzed and the design can be evaluated that enhance the design science and reliability. 1.
From its inception of three-cone drill, there has been the constant pursuit of science and technology workers to improve product quality.
In short, the design of the cone bit is optimized with optimization and computer technology, switching the approximate calculation got by designers’ experience or similar methods to accurate theoretical calculation of the parameters, so that a drill design step into science design stage from the experience trial method.
This greatly improve the accuracy of the bit design, scientific and reliable, and reduce the blind trial and repeated trial times, manpower and material resources, the bit of the development cycle and the development costs of new products and significantly improve the design quality of the bit. 4.
Ma, JJAzar: Dynamics of Roller Cone Bits, Trans.ASME, Journal of Energy Technology, Dec.1985, p. 543–548

Experimental Materials and Methods.
All reagents were commercial grade materials and were used without further purification.
Pure silicon carbide powder (an average of 10 mm grain size) were used as main Microwave heater material.
Hassan , Growth of nanostructured CdO by solid-vapor deposition, International Journal of the Physical Sciences, Vol. 6, No.17 (2011), 4176-4180 [4].
J.G.Lu, P.Ch.Zh.Fan, Quasi-one-dimensional metal oxide materials-Synthesis , properties and applications”, Mater.

Materials used were organic phase change material (n-octadecane) of 99% purity melting temperature of 28 °C used as dispersion media and TiO2 nano-powder of 99.5% purity and average diameter size of 30±5 nm.
Zhu, Y.S.Yin, Y.S.Lin, A novel one-step chemical method preparation of copper nanofluids, Journal of Colloid and Interface Science, 227, 100-130, 2004
Jedsadaratanachai, Heat transfer enhancement of TiO2/water nanofluid in a heat exchanger tube equipped with overlapped dual twisted-tapes, Engineering Science and Technology, an International Journal, 18, 336-350, 2015
Thermal Science, 44, 367-373, 2005
Mataoui, A review on how the researchers prepare their nanofluids, International Journal of Thermal Sciences, 76, 168-189, 2014

Introduction Nano-sized manganese oxides are the one of most important attracted considerable interest materials in various industries, such as rechargeable lithium batteries, electrochemical supercapacitors, electronics, catalysis, and sensors.
The prepared δ-MnO2 material exhibits high capacitance value and good cycling behavior.
Experimental Materials and Synthesis.
Favier, Structural in situ study of the thermal behavior of manganese dioxide materials: toward selected electrode materials for supercapacitors, ACS.
Reddy, Synthesis and electrochemical characterization of amorphous MnO2 electrochemical capacitor electrode material, Journal of Power Sources. 132 (2004) 315–320

Strength properties of the material decrease with increasing of annealing temperature whereas, on the contrary, plastic properties increase.
Experiment The initial material was in the form of pickled cuts of the hot rolled strip with thickness of 3.9 mm.
It is possible to say that up to a value of deformation degree ε = 30 % virtually no recrystallization occurs and the material undergoes work hardening.
Journal of Material Science, 26, 1991, No. 19, p. 5158-5162
[4] Information on http://www.fmmi.vsb.cz/model [5] Deformation Behaviour and Properties of Selected Metallic Materials.

For the sand, the material type 147 was used.
This is an isotropic material model with damage.
The balsa has been considered as orthotropic material.
The authors also acknowledge support of the Institute of Thermomechanics AS CR, v.v.i. of the Czech Academy of Sciences through the project No.
Covey, Blast and Fragment Injuries of the Musculoskeletal System, The Journal of Bone and Joint Surgery 84 (2002) 1221-1234

Further, resistance welding of magnesium requires a backup plate made of steel to conduct the heat to the workpiece material.
This led the automobile manufacturers for the increased use of magnesium alloy base materials for manufacturing automotive components.
Currently resistance spot welding is generally used in welding automotive materials mainly composing of steels.
After 1200 rpm, the frictional heating is high such that material flow occurs while spot welding.
Li, Friction Stir Spot Welding, (2014), A Review on Joint Macro and Microstructure, Property, and Process Modelling, Advances in Materials Science and Engineering Volume, Article ID 697170, 11 pages [3] Zhaohua Zhang, Xinqi Yang, Jialong Zhang, Guang Zhou, Xiaodong Xu, Binlian Zou, (2011), Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy, Materials and design, vol 32, pp. 4461-4470 [4] N.

However, the extreme characteristic of SiC makes it a difficulty to machine material [2].
All these investigations geared toward understanding of the behavior of ceramic materials under machining.
Experimental Details Work-Piece Material and Cutting Tool.
Porto: Ductile and Brittle modes in Single point Diamond turning of silicon probed by Raman Scattering, Journal of Material Science Letters 18(1999), p. 1185-1187
Ramanath: Mechanical of material removal in the precision grinding of ceramics.