Search results

Costaf a,b,c,d,e,f Graduate Program in Materials Science and Engineering – UFRN – Campus Natal, Avenida Senador Salgado Filho, 3000 - Lagoa Nova - Natal - RN, CEP 59078-970, Brasil.
After alkaline treatment, desilication of these materials was observed.
Jong: Journal of Catalysis Vol. 276 (2010), p. 170
Ramirez: Microporous and Mesoporous Materials Vol. 87 (2005), p. 153
Olsbye: Microporous and Mesoporous Materials Vol. 132 (2010), p. 384.

Materials and Methods Experimental setup.
Fig. 1 Combined superheated steam and hot air drying experimental process flow Materials.
Especially it is suitable for drying materials that needs soft drying in the late drying period.
Acknowledgements The authors express their sincere appreciation to the Shandong Provincial Natural Science Foundation of China (No.
Journal of Food Engineering, 95(2): 313-321(2009).

The production cycle of shafts is longer, and quantities of materials is larger, so study of repair technology of shaft is consistent with the goal of green manufacturing, and can promote economic development. 1.
Surface preparation of shafts refers to the purification and roughing treatment of the substrate surface to meet requirements of cleanliness and roughness, so that the coating can combine with substrate materials. 2.1.2 Preheating of shafts in boats and ships The purpose of preheating is to remove water of the surface adsorption, reduce shrinkage stress during the cooling, and improve the bonding strength.
Arc spraying has the arc as heat source, so spraying material must be conductive, usually only metal materials (non-metallic materials can be sprayed if it is cored wires) [4].
Journal of Hunan Institute Engineering, 2011, 21(2): 25~27 [3] Wang Chun-yu, Bu Fan-yu.
Automobile Technology and Material, 2004, 12: 3-5 [10] Wu Ding-cai.

LSP is not a thermal rather a mechanical process for treating materials.
[5] Deng Qilin, Yu Chengye, Zhang Yongkong, Tang Yaxin, experimental research of the improvement of properties of lase shocked aviation aluminium alloys against fatigue fracture, Chinese Journal of Laser, Vol.
Mukherjee, laser shock processing on CVD-processed alumina coat carbide inserts, the Third Pacific Rim International Conference on Advanced Materials and Processing
[8] Zhang Yongkong, study on improvement fatigue life of aviation materials by laser shock strengthening, PhD. thesis.
Hallouin, Comparison of two new surface treatment process, Laser-induced shock waves and primary explosive: application of fatigue behaviour, Material Science and Engineering A 156(1992).

New Large-Size Three-Dimensional Optical Measuring System Investigation JinSongWang 1, a, JianLiu1, b, LiJuanLi1, c, ShanLiu1, d, ZhiYongAn1,e 1 Department of Optical Engineering, Changchun University of Science and Technology, Changchun 130022, China； asoldier_1973@163.com;bljmz1988@163.com;cjuancust@126.com ; dlshan1006@yahoo.com ;ean_zhiyong@126.com Keywords: Optical measuring; Three-dimensional; Large-size; Optic fiber Abstract: In this paper a new three-dimensional large-size optical measurement system by laser radar has been proposed in combination of double-optic circuit measuring technology, ultra-high frequency modulation technology and laser intellectual tracing and location technology.
The system can measure 3d shape unconnectedly for lager-size object, which has the advantages of high accuracy, automatic measurement and freedom from being influenced by material and light ray.
Introduction With the rapid development of modern science and technology, research in optical topography measurement of three-dimensional large-size technology is penetrating day by day.
Journal of Zhejiang University (Engineering Edition), 2006, 40 (12) : p.98 ~ 102

Journal Citation (to be inserted by the publisher ) Copyright by Trans Tech Publications Mechanically Induced Phase Transformation of αααα- and ββββ-Tricalcium Phosphate J.
The process increased the thermodynamic solubility compared to the unmilled materials and accelerated the normally slow reaction with water to form single component cement systems.
Crystal sizes and quantitative phase compositions of the materials were calculated by means of total Rietveld refinement analysis with the TOPAS software (Bruker AXS, Karlsruhe, Germany).
Hydroxyapatite and Related Materials (CRC-Press, USA 1994) p. 127
(Elsevier Science USA 1997) p. 481 [7] M.

However, these materials have the characteristics of high strength, corrosion resistance and high temperature resistance.
If some special elements are added into the materials, superior performance will be obtained, and at the same time the materials will be particularly difficult to milling.
At the same time, the chemical reaction may be caused between the blades materials and tools materials which will exacerbate crater wear of tools (as shown in Fig. 3).
However, cutting machinability of materials determine new engine that it is very difficult to be manufactured.
Liu, etc: Mechanical Science And Technology, Vol. 22(2003), No. 2, pp. 177-178.

The crushed column and other columns is the ground floor were all strengthened using jacketing method and provision of additional columns at the crushed column. 1.0 Introduction Structural defects in concrete structures may be caused by earthquake[1], overloading, structural damages, materials deterioration, apart from design and construction faults.
To determine the quality of concrete materials of the existing structural system; ?
The concrete materials and the grade of concrete were also specified as Grade C30 for all concrete works, and aggregates size not exceeding 20 mm, but preference to 12 mm aggregate size for enhancing better concrete matrix as the new concrete had a thickness of 150 mm all round the old columns.
The excavated soil materials was heaped around the trench, then the top of the footing was cleaned and scarified to form key for bonding with the new concrete.
[4] Bhuvaneshwari P and Saravana Raja Mohan K, “Strengthening of Fire-Damaged Reinforced Concrete Short Columns Using GFPPECC Composites”, Arabian Journal of Science and Engineering (2020) 45:8619-8632, https://doi.org/10.1007/s13369-020-04795-x

Experiment 2.1 Materials Cooking oil tar in this study was obtained from a refectory of a high school, which can accommodate 1500 students.
Acknowledgements This material is based upon work funded by Zhejiang Provincial Natural Science Foundation of China under Grant No.
LQ12E04001 and the National Natural Science Foundation of China (No. 51304179).
Journal of the American Statistical Association, 1995, 90: 1200-1224

Application of simulation tools The results of simulation and visualization could also be useful in analyzing the impact of the timetable and capacity of the material handling equipment, location and capacity of inter-operational buffers and production resources for the standards of production capabilities, which include among others: production order due dates, resource utilization and to ensure an acceptable quality of the production system functioning (without deadlocks and starvations).
Krenczyk, The method of the production flow synchronisation using the meta-rule conception, Journal of Materials Processing Technology. 164 (2005) 1301–1308
Grabowik, Integration Production Planning and Scheduling Systems for Determination of Transitional Phases in Repetitive Production, Hybrid Artificial Intelligent Systems, Lecture Notes in Computer Science. 7209 (2012) 274-283
Skołud, Production Preparation and Order Verification Systems Integration Using Method Based on Data Transformation and Data Mapping, Hybrid Artificial Intelligent Systems, Lecture Notes in Computer Science. 6679 (2011) 397–404