Search results

Material-balance calculations were executed for all there phases (oil, brine and gas (N2 and CO2)) after each experiment.
Acknowledgements This work was financially supported by the The Ministry of Science and Technology of the People's Republic of China (2005BA901A13).
Journal of Southwest Petroleum Institute, 2002:24(91):46~49

Experimental details Aluminum samples of 6063 alloy with size of 30×25×3mm 3 were used as the substrate material.
Acknowledgements The financial aid of the Important Project of Science and Technology Department of Zhejiang Province under grant No. 2006C11183 is gratefully acknowledged.
Technol.Vol.188:199 (2005), p.184, [12]Yang Guangliang , Lu Xianyi , Bai Yizhen, Cui Haifeng and Jin Zengsun: Journal of Alloys and Compounds Vol. 345 (2002), p.196.

While these numbers provide an idea of the sensitivity of tribological parameters to materials in contact, they may not necessarily be representative of the friction coefficients and residual stresses that will result between the wiper and workpiece.
Friction between high speed gear coupling teeth, ASME Journal of Mechanical Design 103 (1981) 54-60
Dynamic behavior of gear systems and variation of coefficient of friction and efficiency during engagement cycle, ASME Journal of Engineering for Industry (November) (1975) 1274-1280
Sliding friction-induced non-linearity and parametric effects in gear dynamics, Journal of Sound and Vibration 248 (4) (2001) 671-694
PROGRI, Load transmission by elastic, elasto-plastic or fully plastic deformation of rough interface asperities (2001), Mechanics of Materials, Vol. 33, pp. 617-633

Due to their small size and high surface area to volume ratio, nanomaterials have a different UV blocking capacity from bulk materials [15].
Materials had reflection maxima at 77 degrees of glancing angle.
The materials' nanocrystalline structure was suggested by the large reflection peaks.
The materials have a tetragonal crystalline structure with lattice constants of 1.2291 to 8.6147, which is consistent with JCPDS No 65-4028.
Availability of the Data and Materials There is no data availability for the reproduction.

Study of the Possibility of Production of Continuously Cast Billets From Shipbuilding Steels Arif Mammadov1,a,*, Nizami Ismayilov2,b, Elxan Mammadov2,c, Muxtar Huseynov1,d 1Faculty of Metallurgy and Materials Science, Department of Metallurgy and Materials Technologies, Azerbaijan Technical University, Az1073, Baku, Azerbaijan Republic 2Faculty of ship navigation, Departments of Shipbuilding and Ship Repair, Azerbaijan State Marine Academy Az1000, Baku, Azerbaijan Republic aariff-1947@mail.ru, bnizism@mail.ru, celxan.mammadov@asco.az, dmuxtar.53@mail.ru Keywords: shipbuilding steels, continuously cast billets, steel casting, degasser installation, magnetic mixing Abstract: The importance of creating specialized production sites to meet the needs of shipbuilding and ship repair enterprises of Azerbaijan in metal billets is substantiated.
Since the requirements of the separation policies are not recognized in our country, these metal materials are brought only from the external countries.
Materials and Methods In order to ensure the high quality of the oil mills in the company "Baku Steel Company" MMC, the construction and testing of a new intermittent assembly machine is carried out.
Aliyev report materials, Baku, 2022, p. 31-33
Mechanical engineering materials.

Glass fiber reinforced materials possess high mechanical strenghth and excellent wear resistance.
As a filler, talc is widely used in composite materials [12,13] for example, to improve the strength, hardness, and abrasive resistance of various types of materials in the plastics industry.
Hyperthermal AO reacts with polymer materials, which causes mass loss or changes in surface morphology.
Fusaro, Evaluation of several polymer materials for use as solid lubricants in space, Tribol.
Rickman, Oxygen interactions with materials III—mission and induced environments, J.

Tatu, Optimal design of the solar tracker used for a photovoltaic string, Journal of Renewable and Sustainable Energy, vol. 5, nr. 2 (2013), pp. 023133 (1-16)
Alexandru, Optimal design of the mechanical device for a photovoltaic tracking mechanism, Applied Mechanics and Materials, vol. 186 (2012), pp. 114-123
Calabrò, Determining optimum tilt angles of photovoltaic panels at typical north-tropical latitudes, Journal of Renewable and Sustainable Energy, vol. 1, no. 3 (2009), pp. 033104 (1-6)
Alexandru, Software platform for analyzing and optimizing the mechanical systems, Proceedings of the 10th IFToMM International Symposium on Science of Mechanisms and Machines, Springer, pp. 665-677 (2009)
Ceccarelli, Challenges for mechanism design, Proceedings of the 10th IFToMM International Symposium on Science of Mechanisms and Machines, Springer, pp. 1-13 (2009)

Materials and Methods Nozzle flow model test system A nozzle flow model test system, which includes a computer, a PWM waveform generator and a liquid supply unit, is developed as shown in Fig. 1.
Acknowledgements The study is supported by China national science and technology project (2011BAD20B06), China Shaanxi province science and technology project (2011K02-05) and China national “948” project of the Ministry of Agriculture (2011-G32).
References [1]Hang Zhu, Yubin Lan, Wenfu Wu, et al., Development of a PWM Precision Spraying Controller for Unmanned Aerial Vehicles, Journal of Bionic Engineering 7 (2010) 276–283 [2]Li Li, Jianli Song, Xiongkui He, Design and Application of Crop Automatic Target Detection Device, Transactions of the Chinese Society for Agricultural Machinery, 41 (2010) 54-56.
Status Analysis of Precision Pesticide Application Techniques, Journal of Agricultural Mechanization Research 5(2010) 9-12.
[12]Zou Wei, Li Li, Wang Xiu, et al., Variable Pesticide Spraying System Based on PWM Speed Control, Journal of Agricultural Mechanization Research 2(2010) 163-166.

Virtual reality technology is a hot research topic in computer science and the introduction of virtual roaming to the field of urban planning provides a new means for urban design.
References [1] Katsushi Ikeuehi, Masao Sakauchi et al: Constructing Virtual Cities by Using Panoramic images, Intenational Journal of Computer Vision,2004,58(3):237-247 [2] Kyshik oh: Landscape Information System:AGIS approach to managing urban development,Landscape and Urban planing,2001,54(4):79-59
[8] Pu Liu, Zhenghong Peng: Three-dimensional Modeling of Virtual City: Taking MultiGenCreator, Advanced Materials Research,Feb2013 [9] JinhuiHu, SuyaYou, Ulrieh Neumann: Approaches to lagre-scale ubran modeling.

We identified that the Online Learning Experience, or the technological resources, tools, and materials available, would achieve the Collaborative Learning Experience, or the activities and interactions.
These approaches placed learners/users as self-determined learners or ‘agents of change’, promoting autonomy to explore and interpret the resources, materials and the online environment and build their learning pathway.
Reflective Journals.
It helps gather information about a fashion brand, fashion consumers, market trends, socio-economic scenarios, materials, resources, and technical constraints during the development of a fashion collection.
In IOP Conference Series: Materials Science and Engineering, 459(1), 012043.