Search results

Samuel, Review various aspects involved in the production of low- hydrogen aluminium castings, Journal of Materials Science 27 (1992) 6533-6563

At the same time, the well liquid supply and dynamic liquid level materials should be taken into consideration to determine whether the requirements for pumping and flowing are satisfied.
Journal of Petroleum Science and Engineering, 2007, 43-48 [4] De Lima, Guedes, Sliva.

Tab.1 Similarity coefficients of the bridge model Type Physical quantity Dimension Similarity coefficient Geometry Linear displacement l [L] SL=1/16 Angular displacementδ [L] Sδ =1/16 Material property Stress σc [FL-2] =0.901 Strain εc — = 1 Elastic module Es [FL-2] =0.901 Density ρc [FL-4T2] , take 1 Load Concentrated load P [F] =0.0059 Bending Moment M [FL] =0.000244 The main arch rib is composited of one steel pipe with diameter 110mm and wall thickness 2mm, and two steel pipes with diameter 75mm and wall thickness 1.5mm.
The natural frequency, damping ratio and mode shape is related to the structural type, mass distribution, stiffness, material property and boundary conditions [8-10].
An overview of concrete and CFST arch bridges in China, ARCH’07 – 5th International Conference on Arch Bridges, 29-44. (2007) [4] Sheng Hongfei, Guo Wei, Wang Rui, The nonlinear analysis of concrete filled steel tubular Half Trough Arch Bridge without Wind Brace, Journal of Harbin University of C·E·& Architecture, 30(4):103-107. (1997) (in Chinese) [5] Cao Guohui, Fang Zhi, Zhou Xianyan, Experimental study on concrete-filled steel tube tied-arch bridge with CFRP hangers, China Civil Engineering, 39(12): 73-78. (2006) (in Chinese) [6] Yang Rihua, The analysis on mechanical property of Maocaojie long-span bridge model test, Changsha, China, Changsha University of Science & Technology, 2005.

Table 1 The main statistical parameters of Cu, Cd, Zn, Cr ,As, Hg and Pb in the fine river sediments Unit [ppm] Element Cu Pb Zn Cd Cr As Hg Average value (n=66) 435.2 3601.2 779.9 7.1 52.7 4.4 3.8 Median 265.0 2395.0 244.0 2.3 44.8 4.1 2.7 Variance 506.0 4031.8 1607.3 15.4 29.1 1.2 4.2 Standard deviation 3240.0 21825.0 9000.0 89.6 178.0 8.9 24.6 Maximum value 32.3 51.0 32.0 0.2 1.4 2.6 0.8 Minimum value 1.16 1.12 2.06 2.16 0.55 0.28 1.12 Coefficient of variation 435.2 3601.2 779.9 7.1 52.7 4.4 3.8 Fig.3 Frequency distribution diagrams of Hg, Pb, Cu, Fe, As, Cd, Zn and Cr in the sediments In this sense, one of the most important points in geochemical prospecting is the selection of threshold values to separate the regional background (understood as the mean content of each element considered in a geological material) and the positive geochemical anomalies, i.e
In this sense, one of the most important points in geochemical prospecting is the selection of threshold values to separate the regional background (understood as the mean content of each element considered in a geological material) and the positive geochemical anomalies, i.e. unusually high contents of those elements in that particular geological context.
Acknowledgements This work was financially supported by the Nation Natural Science Foundation (200811061), and The Project of Nation Geologic Investigation (1212010741003).
Zonation of contaminated bottom sediments in Hamilton harbour as defined by statistical classification techniques,Water Quality Research Journal of Canada.31(1996) 505–528

Zhang: Virtual Reality System (Science press, China 2001) [2] X.N.
Yao: Key Engineering Materials, Vol.316 (2006), pp.556-560
Liu: The International Journal of Advanced Manufacturing Technology, Vol.3 (2006), pp.395-402.

This value has been confirmed through experimental calibration using a range of material types, stress histories and stress levels [5,6].
During the consolidating procedure of soil deposits, the nozzle can be replaced with sample profile or trimming tools if a specific surface or material removal is required.
This research is supported by National Natural Science Foundation of China 50909014.
International Journal of Physical Modelling in Geotechnics, 2001, 1(3): 17-25

Series: Materials Science and Engineering, 33(2012) 012086
Journal Heat and Mass Trans. 51 (2008) 3399 - 3409.

It was awarded by the National Council of Science and Technology (CONACyT).
Progress and Prospects," Journal of Pressure Vessel Technology, vol. 122, pp. 339-348, 2000
[19] ANSYS, "Workshop 09 Fluent Introduction," in Customer Training Material, USA, ANSYS, 2016, p. 14. [20] ANSYS, "Lecture 10 Fluent Introduction," in Customer Training Material, USA, ANSYS, 2016, p. 9.

For example, a gripper from the robot system will be matched against an item in the process, taking into account attributes as the weight, dimensions and material properties of the item and attributes such as the valid payload, and grasping methods of the gripper.
Gravot, A hybrid approach to intricate motion, manipulation and task planning, The International Journal of Robotics Research, vol. 28, no. 1, (2009) 104–126
Long, An Extension to PDDL for Expressing Temporal Planning Domains (PDDL2.1), Journal of Artificial Intelligence Research, Vol. 20, No. 20, AI Access Foundation, (2003) 61-124
Schlette, The Simulation and Animation of Virtual Humans to Better Understand Ergonomic Conditions at Manual Workplaces, The Journal on Systemics, Cybernetics and Informatics (JSCI), Volume 8. (2010) [18] N.
Rossmann, Symbolic Planning for Industrial Applications – the eRobotics Approach, Proceedings of the IEEE International Conference on Automation Science and Engineering (CASE), IEEE, ISBN 978-1-4799-5283-0. (2014) [19] F.

Ishlinsky Institute for Problems in Mechanics of the Russian Academy of Sciences 119526 Moscow, pr.
A wide range of abrasive materials is used in the CMP processes.
Note, that to estimate the crack opening one can neglect by a difference of deformation properties of contacting materials loading to some tangential forces.
[12]　K.Smehalin, D.Fertig, Microscale dishing effect in a chemical mechanical planarization process for trench isolation, Journal of Electrochemical Society. 143 12 (1996) 1281-1283
Steigerwald, S.P.Murarka, R.J.Gutman, Chemical-mechanical planarization of microelectronic materials, John Wiley & sons, Inc., New York, 1997