Influence of Wear and Backlash on Machined PEEK Polymer Bushes and 7075 Aluminium Alloy Cam Plates Used in Robot Joints

Abstract:

Due to constant exposure to high torque and loads toughness, compressive durability and light weight of joint parts are crucial factors for biped walking humanoid robot parts. When polymer transmission parts are used for the manufacture of humanoid robot joint, wear becomes an important factor in terms of transmission error (backlash) between the input and output axes, ex. between the motor and the robot’s leg joint. In such joint system, a polymer bushes is directly connected to a cam plate, playing an important role in the robot's movement ability. In this work, the influence of wear of reinforced poly-ether-ether-ketone (PEEK) polymer bushes in friction against 7075 aluminium alloy cam plates is investigated in order to establish the application possibilities in transmission parts in humanoid robot’s joint. The PEEK bush surface conditions as well as the input axis-output axis backlash require close examination, so that efficient systems can be built. Sliding wear tests were performed on bushes under 0-50kgfcm loaded torque while the cam plate oscillated. Based on the wear observation, it was found that in a high load range the backlash increased along with number of cycles due to PEEK bush wear. The bush surface roughness also increased during testing. Roughness of PEEK bush surface and the loaded torque for output axis were significantly related to backlash of output axis in robot joint.

• Periodical: Applied Mechanics and Materials (Volumes 157-158)
• Pages: 1178-1185
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.157-158.1178
• Online since: February 2012
• Authors: Hitonobu Koike, Katsuyuki Kida, Kenji Kanemasu, K. Itakura, Kenichi Saruwatari, Justyna Rozwadowska, Megumi Uryu
• Keywords: 7075 Aluminum Alloy, Backlash, PEEK, Robot Joints, Sliding Wear

References

[1] N. Shirokoshi: Studies of Influences of Geometrical Errors to Final Performances in Small Backlash Planetary Gears, JSME vol66-646(2000-6).

[2] T. Oguri: Backlash compensation of reduction gears by twin moter cooperative control 602 JSME 145-146(2006).

[3] K. Nagamura,T. Koumori: Driving Performance of High Reduction Planetary Gear Drive with Arc Tooth Profile and Pin, 123 JSME 103-106 No. 07-15(2007).

DOI: 10.1115/detc2007-34245

[4] K. Gotouda: Experimental Analysis about the Influence of Alignment Error on Transmission Error of Planetary Gears; JSME vol4, 37-38(2008).

[5] S. Yanabe: Torsional stiffness of Harmonic Drive Reducers, JSME, vol55-509, pp.216-221 (1989).

[6] M. Hashimoto, I. Godler: Built-in High Accuracy Torque Sending For Harmonic Drive Gears, JRSJ, vol15-5, pp.802-806(1997).

DOI: 10.7210/jrsj.15.802

[7] Y. Kiyosawa: Introduction of Ultra Flat Strain Wave Gearing, JSME, No04-17, pp.76-79 (2004).

[8] N. Ito,H. Hasegawa: Robust Optimization of the Gait for a Biped Robot on External Factors, JSME, No08-35 (2008) , 47-52.

[9] C. Sabourin,O. Bruneau: Robustness of the dynamic walk of a biped robot subjected to disturbing external forces by using CMAC neural networks, Robotics and Autonomous Systems 51(2005)81–99.

DOI: 10.1016/j.robot.2005.02.001

[10] J. Hanchi, N.S. Eiss, Jr: Dry sliding friction and wear of short carbon-fiber-reinforced poly-ether-ether-ketone (PEEK) at elevated temperatures, Wear 203-204 ( 1997) 380-386.

DOI: 10.1016/s0043-1648(96)07347-4

[11] K. Seto,Y. Yamamoto : Friction and Wear Performance of PEEK and Fiber Reinforced PEEKs under water Lubricated Condition, JSME No-018-1, 191-192(2001).

DOI: 10.1299/jsmekyushu.2001.54.191

[12] Y. Yamamoto, M. Hashimoto : Friction and wear of water lubricated PEEK and PPS sliding contacts, Wear 257, 184-189(2004).

DOI: 10.1016/j.wear.2003.12.004

[13] K. Friedrich, J. Karger-Kocsis, Z. Lu: Effects of counterpart roughness and temperature on friction and wear of PEEK-composites under dry sliding conditions, Wear, 148 (1991), p.235–247.

DOI: 10.1016/0043-1648(91)90287-5

[14] M. Harrass, K. Friedrich, A.A. Almajid: Tribological behavior of selected engineering polymers under rolling contact, Trib. int. 2009 doi: 10. 1016/j. triboint. 2009. 10. 003.

DOI: 10.1016/j.triboint.2009.10.003

[15] DearnKD, KukurekaSN, WaltonD. Engineering polymers and composites for machine elements. In: SinhaSK, BriscoeBJ, editors. Polymer Tribology. London UK: Imperial College Press; 2009. pp.470-505 [Chapter 14].

[16] R.N. Rao, S. Das : Wear coefficient and reliability of sliding wear test procedure for high strength aluminium alloy and composite, Materials and Design 31 (2010) 3227–3233.

DOI: 10.1016/j.matdes.2010.02.017

[17] S. Bahadur, D. Gong and J.W. Anderegg: The investigation of the action of fillers by XPS studies of the transfer films of PEEK and its composites containing CUS and CUF2, Wear, 160, pp.131-138(1993).

DOI: 10.1016/0043-1648(93)90414-h

[18] G. Zhang, Z. Rasheva, A.K. Schlarb: Friction and wear variations of short carbon fiber (SCF) /PTFE/graphite (10 vol. %) filled PEEK: Effects of fiber orientation and nominal contact pressure, Wear 268 (2010) 893–899.

DOI: 10.1016/j.wear.2009.12.001

[19] T. Honda, K. Kida, E.C. Santos, H. Koike, Y. Kashima,K. Kanemasu, Fatigue: Behavior of Machined PEEK Ball Bearings under Rolling Contact Loading in Water, Proc. Processing and Fabrication of Advanced Materials XIX (2011. 01. )pp.515-520.

DOI: 10.4028/www.scientific.net/amr.566.197

[20] H. Nagashima : Study on Friction and Wear Characteristics of Bearing Materials, JSME (2006)9-15.

[21] H. Koike, K. Kida, K. Kanemasu: Influence of wear and thermal deformation on machined PEEK plastic bush and Ti crank shaft, International Congress on Advanced Materials2011, 6054P.

DOI: 10.1177/0967391112020001-223