An Experimental Investigation of the Dynamic Mechanical Behaviors of Hollow Spheres Filled Syntactic Foam

Abstract:

Dynamic mechanical behaviors are critical to the engineering applications of hollow spheres filled syntactic foams. The potential of such composites cannot be fully realized unless the effects of strain rate on their mechanical properties are fully understood. In this study, both the compressive and the tensile behaviors of an epoxy syntactic foam filled by ceramic microspheres were experimentally investigated over the strain rate range from 0.001 to 2000 s-1. The compressive and tensile tests at high strain rates were carried out by means of split Hopkinson pressure bar (SHPB) and split Hopkinson tensile bar (SHTB), respectively. The stress-strain responses and failure mechanisms were examined quantitatively and qualitatively. The experimental results indicate that both the compressive and the tensile behaviors of syntactic foam are highly sensitive to strain rate. Moreover, a comparison of the stress-strain curves suggests that the compressive and tensile behaviors are dominated by different failure mechanisms, which consequently lead to distinct effects of strain rate on the compressive and tensile behaviors of syntactic foam.

• Periodical: Applied Mechanics and Materials (Volumes 268-270)
• Pages: 67-73
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.268-270.67
• Online since: December 2012
• Authors: Ming Yu, Ping Zhu
• Keywords: Compressive Properties, Dynamic Behavior, Split Hopkinson Bar, Strain Rate Sensitivity, Syntactic Foam, Tensile Properties

References

[1] L. Bardella, F. Genna: Int J Solids Struct Vol. 38 (2001), p.7235

[2] J.B. Hinves, C.D. Douglas: IEEE Vol. 3 (1993), p.468

[3] A. Corigliano, E. Rizzi, E. Papa: Compos Sci Technol Vol. 60 (2000), p.2169

[4] L. Bardella, F. Genna: Int J Solids Struct Vol. 38 (2001), p.307

[5] E.S. Weiser, T.F. Johnson, T.L.S. Clair, et al: High Perform Polym Vol. 12 (2000), p.1

[6] E.M. Wouterson, F.Y.C. Boey, X. Hu, et al: Compos Sci Technol Vol. 65 (2005), p.1840

[7] G. Tagliavia, M. Porfiri, N. Gupta: Composites Part B Vol. 41 (2010), p.86

[8] N. Gupta , R. Ye, M. Porfiri: Composites Part B Vol. 41 (2010), p.236

[9] A. Das, B.K. Satapathy: Mater Des Vol. 32 (2011), p.1477

[10] C. Swetha, R. Kumar: Mater Des Vol. 32 (2011), p.4152

[11] M. A. Elhadek, H.V. Tippur: J Mater Sci Vol. 37 (2002), p.1649

[12] Kishore, R. Shankar, S. Sankaran: J Mater Sci Vol. 41 (2006), p.7459

[13] E. Woldesenbet, S. Peter: J Mater Sci Vol. 44 (2009), p.1551

[14] L. Zhang, J. Ma: Compos Sci Technol Vol. 70 (2010), p.1265

[15] M. Yu, P. Zhu, Y. Ma: Comput Mater Sci Vol. 63 (2012), p.232

[16] H. Kolsky: Proc R Soc Lond B Vol. 62 (1949), p.676

[17] P. Li, N. Petrinic, C.R. Sivioura, et al: Mat Sci Eng A Vol. 19 (2009), p.515