Some Aspects Regarding Micro-Scale EDM Drilling Process

Abstract:

The abstract should be written after the paper is finished; it should state briefly the research problem, research methods and research results. The abstract length will not exceed 250 words. This template explains and demonstrates how to prepare your camera-ready paper for Trans Tech Publications. The best is to read these instructions and follow the outline of this text. Please make the page settings of your word /left margins must be 2 cm (0.78 in). % by the publisher. Please keep this in mind when designing your figures and tables etc.

• Periodical: Applied Mechanics and Materials (Volume 371)
• Pages: 285-289
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.371.285
• Online since: August 2013
• Authors: Oana Dodun, Carmen Ema Panaite, Lorelei Gherman
• Keywords: Accuracy, Electrical Discharge Machining (EDM), Electrode Wear Rate, Hole Drilling, Material Removal Rate (MRR), Micro Machining

References

[1] U. Maradia, M. Boccadoro, J. Stirnimann, I. Beltrami, F. Kustera and K Wegener, Die-sink EDM in meso-micro machining, Procedia CIRP 1 (2012) 166 – 171.

DOI: 10.1016/j.procir.2012.04.029

[2] M.P. Jahan, Y.S. Wong, M. Rahman Evaluation of the effectiveness of low frequency workpiece vibration in deep-hole micro-EDM drilling of tungsten carbide, Journal of Manufacturing Processes 14 (2012) 343–359.

DOI: 10.1016/j.jmapro.2012.07.001

[3] K.P. Rajurkar, G. Levy, A. Malshe, M.M. Sundaram, J. McGeough, X. Hu, R. Resnick and A. DeSilva, Micro and nano machining by electro-physical and chemical processes, CIRP Ann. Manuf. Technol. 55 (2) (2006) 643–666.

DOI: 10.1016/j.cirp.2006.10.002

[4] Y. Yahagi, T. Koyano, M. Kunieda, and X. Yang, Micro Drilling EDM with High Rotation Speed of Tool Electrode Using the Electrostatic Induction Feeding Method, Procedia CIRP 1 (2012) 162 – 165.

DOI: 10.1016/j.procir.2012.04.028

[5] E. Bamberg, S. Heamawatanachai , Orbital electrode actuation to improve efficiency of drilling micro-holes by micro-EDM, Journal of materials processing technology 2 0 9 ( 2009) 1826–1834.

DOI: 10.1016/j.jmatprotec.2008.04.044

[6] D. Ghiculescu, N. I. Marinescu, G. Jitianu and G. Seritan, On precision improvement by ultrasonics-aided electrodischarge machining, Estonian Journal of Engineering 15 1 (2009) 24–33.

DOI: 10.3176/eng.2009.1.03

[7] L. Jianzhong, Y. Guoqiang, W. Cong, G. Xuejie and Y. Zuyuan, Prediction of aspect ratio of a micro hole drilled by EDM, Journal of Mechanical Science and Technology 27 (1) (2013) 185-190.

DOI: 10.1007/s12206-012-1214-9

[8] Z.Y. Yu, T. Masuzawa, M. Fujino, Micro-EDM for Three-Dimensional Cavities – Development of Uniform Wear Method, CIRP Ann. Manuf. Technol. 47, issue 1 (1998) 169–172.

DOI: 10.1016/s0007-8506(07)62810-8