Effect of Laser Beam Diameter on Cut Edge of Steel Plates Obtained by Laser Machining

Abstract:

Laser cutting is a thermal process which is used contactless to separate materials. In the present study, high-power laser cutting of steel plates is considered and the thermal influence of laser cutting on the cut edges is examined. The microstructure and the microhardness of the cut edge are affected by the input laser cutting parameter: laser beam diameter. The aim of this work is to investigate the effect of the laser beam diameter on the microhardness beneath the cut surface of steel plates obtained by CO2 laser cutting. The cut surface was studied based on microhardness depth profiles beneath the machined surface. The results show that laser cutting has a thermal effect on the surface microstructure and on the microhardness beneath the cut section. Also the microhardness of the hardening zone depends on the laser beam diameter.

• Periodical: Applied Mechanics and Materials (Volume 467)
• Pages: 227-232
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.467.227
• Online since: December 2013
• Authors: Imed Miraoui*, Mouna Zaied, Mohamed Boujelbene
• Keywords: Laser Beam, Laser Cutting, Microhardness, Microstructure, Steel Plates

References

[1] N. B. Dahotre, S. P. Harimkar. Laser cutting. Laser fabrication and machining of materials, book chapter 5 (2008) 144-206.

[2] N. Jebbari, M.M. Jebari, F. Saadallah, A. Tarrats, R. Bennaceur, J.P. Longuemard, Themal affected zone obtained in machining steel XC42 by high-power CO2 laser, Optics and Laser Technology, vol. 40, p.864–873, (2008).

DOI: 10.1016/j.optlastec.2007.11.006

[3] I. Decker, J. Ruge, U. Atzert, Physical models and technological aspects of laser gas cutting, Proceeding of SPIE, Industrial applications of high power lasers, vol. 4, p.81–88, (1984).

DOI: 10.1117/12.966211

[4] D. Pantelis, Laser de puissance, traitement et utilization, " Techniques de l, ingénieur, vol. AF3, no A1095, (1992).

[5] N. Ben, C. Chen, L. Furong, Optimization on the fiber laser micro-cutting of thin stainless steel sheet by artificial neural networks, , Advanced Science Letters, vol. 4, p.810–813, (2001).

DOI: 10.1166/asl.2011.1452

[6] M. Radovanovic, P. Dasic, Rresearch on surface roughness by laser cut, , The Annals of University Dunarea de Jos of Galati Fasicule VII, Tribology, pp.84-88, (2006).

[7] I. Miraoui, E. Elimi, M. Boujelbene, E. Bayraktar, Analysis of roughness and microstructure for high-power laser cutting of stainless steel, Advanced Science Letters, vol. 19, pp.483-486, (2013).

DOI: 10.1166/asl.2013.4775

[8] C. Esposrro and G. Daureli, Tuning of a parametric model for the laser cutting of steels, Optics and Lasers in Engineering, vol. 2, pp.161-171, (1981).

DOI: 10.1016/0143-8166(81)90017-8

[9] H. Hocheng and C. T. Pan, Section area of heat affected zone in laser cutting of carbon fiber-reinforced PEEK, , Machining of advanced composites, vol. 66, (1993).

[10] I. Miraoui, M. Boujelbene and E. Bayraktar, Effects of laser cutting main parameters on microhardness and microstructure changes of stainless steel, , Advanced Materials Research, vol. 664, pp.811-816, (2013).

DOI: 10.4028/www.scientific.net/amr.664.811

[11] K. Weman, Welding Process Handbook, , CRC Press LLC, New York, (2003).

[12] N. Rajaram, J. Sheikh-Ahmad and S.H. Cheraghi, CO2 laser cut quality of 4130 steel, International Journal of Machine Tools & Manufacture, vol. 43, pp.351-358, (2003).

DOI: 10.1016/s0890-6955(02)00270-5

[13] F. Quintero, J. Pou, F. Lusquinos, M. Boutinguiza, R. Soto, M. Amor, Quantitative evaluation of the cuts performed on mullitealumina by Nd: YAG laser, Opt Lasers Eng, vol. 42, pp.327-340, (2004).

DOI: 10.1016/j.optlaseng.2003.10.001

[14] J. Grum, D. Zuljan, Analysid of heat effects in laser cutting of steel,J. Mat. Eng. Perform, vol. 5, pp.526-537, (1996).