Numerical Simulation of Superheated Steam Flow in a Micronozzle

Abstract:

Methods for creating thrusters with very low thrust using micronozzles have been actively developed recently. The propellant flow in such micronozzles are pressure driven and are characterized by low Reynolds number. Hence, the flow is always in laminar regime with high viscous losses. Proper design by effectively studying the flow behavior of propellant inside micronozzle is highly essential to minimize the losses. The geometry of the micronozzle is a key factor that affects the performance of the thruster. In this paper numerical examinations of the flow of superheated steam inside a 3D pyramidal micronozzle by solving Navier stoke’s equation with no slip boundary condition and equation of energy conservation. The computational model is validated with available experimental data in the literature. The computations are performed for different mass flow rates and inlet vapour temperatures increased until the exit temperature reaches the saturation temperature of the vapour. The study provides the insight into analysis of flows in the complicated microdevices.

• Periodical: Applied Mechanics and Materials (Volumes 592-594)
• Pages: 1677-1681
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.592-594.1677
• Online since: July 2014
• Authors: P.A. Haris*, T. Ramesh
• Keywords: Micro Nozzle, Micro Thruster

References

[1] J. Mueller, W.C. Tang, A.P. Wallace, W. Li., D. Bame, I. Chakraborty, R. Lawton, Design analysis and fabrication of a vapourizing liquid microthruster, AIAA Paper 97-3054, Seattle, WA, USA, July (1997).

DOI: 10.2514/6.1997-3054

[2] D.K. Maurya, S. Das, S.K. Lahiri, An analytical model of a silicon MEMS vapourizing liquid microthruster and some experimental studies, Sensors and Actuators A 122 (2005) 159–166.

DOI: 10.1016/j.sna.2005.04.020

[3] E.V. Mukerjee, A.P. Wallace, K.Y. Yan, et al., Vapourizing liquid microthruster, Sensors and Actuators A 83 (2000) 231–236.

DOI: 10.1016/s0924-4247(99)00389-1

[4] X.Y. Ye, F. Tang, H.Q. Ding, Z.Y. Zhou, Study of a vapourizing water micro-thruster, Sensors and Actuators A 89 (2001) 159–165.

DOI: 10.1016/s0924-4247(00)00540-9

[5] C.C. Chen, C.W. Liu, H.C. Kana, et al., Simulation and experiment research on vapourizing liquid micro-thruster, Sensors and Actuators A 157 (2010) 140–149.

[6] Pijus Kundu, Tarun Kanti Bhattacharyya, Soumen Das, Design, fabrication and performance evaluation of a vapourizing liquid microthruster, J. Micromech. Microeng. 22(2012) 025016 (15pp).

DOI: 10.1088/0960-1317/22/2/025016

[7] K. Karthikeyan, S.K. Chou, L.E. Khoong, Y.M. Tan, C.W. Lu, W.M. Yang, Low temperature co-fired ceramic vapourizing liquid microthruster for microspacecraft applications, Applied Energy 97 (2012) 577–583.

DOI: 10.1016/j.apenergy.2011.11.078

[8] J.W. Cen, J.L. Xu, Performance evaluation and flow visualization of a MEMS based vapourizing liquid micro-thruster, Acta Astronautica 67 (2010) 468–482.

DOI: 10.1016/j.actaastro.2010.04.009

[9] Chia-Chin Chen, Heng-Chuan Kan, Ming-Hsiao Lee, Chein-Wei Liu, Computational Study on Vapourizing Liquid Micro-Thruster, International Microsystems, packaging Assembly and Circuits Technology Conference.

DOI: 10.1109/impact.2012.6420277