Modelling of Welded Joint Geometry in Sheet Metal Welding

N.V. Pavlov; А.V. Kryukov; Е.A. Zernin; V.A. Polischuk

doi:10.4028/www.scientific.net/AMM.682.443

Paper Titles

Capacity Calculation of Hydraulic Motors in Geokhod Systems for Justification of Energy-Power Block Parameters
p.418

The Technology of Mig-Mag Welding with Low-Frequency Modulation of Arc Current
p.426

Crack Resistance of Weld Seals, Hardening Methods and Composite Tools Quality
p.431

Influence of Molybdenum Nanopowder Concentration on Welded Joint Microstructure
p.438

Modelling of Welded Joint Geometry in Sheet Metal Welding
p.443

Laws of Development of Deformation Folds in [1^- 11] Copper Single Crystal at Axis Compression
p.448

Formation of Metal–Polymer Composite on Titanium Alloy Surfaces
p.453

Interfacial Adhesion between Thermal Spray Coating and Substrate Achieved by Ultrasonic Finishing
p.459

Scandium Influence on the Structure and Chemical Inhomogeneity of Welded Joints of Al-Zn-Mg-Cu System Alloys
p.464

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 682Modelling of Welded Joint Geometry in Sheet Metal...

Modelling of Welded Joint Geometry in Sheet Metal Welding

Abstract:

The article considers adapted dependence of weld sizes on weld dimensions and impulse electrode wire feed parameters in sheet metal welding. Comparative analysis of test and calculated data for a weld size showed the model adequacy. Further on they were used for developing a computer application “Calculation of sheet metal weld dimensions” which allows to predict the form of a weld in impulse wire feed welding.

You might also be interested in these eBooks

Innovative Technologies and Economics in Engineering

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 682)

Pages:

443-447

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.682.443

Citation:

Cite this paper

Online since:

October 2014

Authors:

N.V. Pavlov*, А.V. Kryukov, Е.A. Zernin, V.A. Polischuk

Keywords:

Computer Application, Highly Concentrated Heat Source, Mathematical Models, Sheet Metal, Welded Joint Geometry

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] I.M. Zhdanov, B.V. Medko, V.N. Nifantov and coauthors. Heat concentration change and heat removal application / Automatic Welding. – 1985. – №5. – P. 51 – 54.

Google Scholar

[2] D.A. Chinakhov, A.V. Vorobyov, A.A. Tomchik Simulation of active shielding gas impact on heat distribution in the weld zone / Materials Science Forum. Volume 762, 2013, Pages 717-721.

DOI: 10.4028/www.scientific.net/msf.762.717

Google Scholar

[3] I.Z. Zasyd'ko, I.P. Korinecy Welding of thin-sheet constructions / Research Bulletin of NTUU KPI, 2010, №5, P. 81-87.

Google Scholar

[4] A.V. Kryukov, N.V. Pavlov, A.A. Zelenkovsky / Welding Production. –2013. –№5. –P. 37 – 39.

Google Scholar

[5] A.G. Krampit, N.Y. Krampit Method for the determination of the geometrical dimensions and area of the welded joint / Welding International. Volume 27, Issue 10, October 2013, Pages 834-836.

DOI: 10.1080/09507116.2013.796637

Google Scholar

[6] B. M Berezovsky. Mathematical models of arc welding: volume 1. Mathematical Modeling and Information Technology, welding pool modes and weld formation /. – Chelyabinsk: South Ural State University, 2002. – 85p.

Google Scholar

[7] Theory on Welding: Textbook for Higher Educational Institutions / Edited by V.M. Nerovny. M.: Bauman Moscow State Technical University. 2007. – 752p.

Google Scholar

[8] I.F. Korinets, Tszi Chzhen Chun. Deterministic and statistical model of a weld form in arc welding / Automatic Welding. – 2001. - №10. P. 44 – 47.

Google Scholar

[9] I.F. Korinets, Tszi Chzhen Chun. The influence of a gap on a butt weld size in welding in Аr + 25% СO2 / Automatic Welding. –2002. - №8. P. 16 – 19.

Google Scholar

[10] N.V. Pavlov, A.V. Kryukov, E.A. Zernin Deterministic and statistical model of a form of a weld in welding with impulse electrode wire feed in a mixture of gases / Welding and Diagnostics. –2011. –№6. P. 31–35.

DOI: 10.1080/09507116.2011.606167

Google Scholar

[11] Patent for an invention №2254969 Wire feed mechanism / Brunov O.G., Fedko V.T., Kryukov A.V. and coauthors. Published 27. 06. 2005. Bull. №18.

Google Scholar

[12] Y.F. Yazykov, I.V. Aleksina Advantages of welding in shielding gases / Welding Production. –2008. –№9. –P. 29 – 30.

Google Scholar

[13] N.V. Pavlov, A.V. Kryukov, E.A. Zernin Welding with impulse wire feed in gas mixture / Welding Production. –2010. –№4. –P. 27 – 28.

DOI: 10.4028/www.scientific.net/amm.379.183

Google Scholar