EDM Process Parameters Optimization Using Taguchi Method

Abstract:

In this paper , the parameters of Electrical Discharge Machine (EDM) are investigated during the machining of Inconel 718 by using different sizes of circular Aluminum electrode. Demand for better surface finishes are increasing recently for all materials, the low rigidity and high material removal rate of Inconel alloys offers a challenging task in obtaining better Surface Finish. The analysis of surface characteristics like Surface Roughness (SR) of Inconel 718 material is carried out an excellent surface finish can be obtained by setting the machining parameters at optimum level. Experimentation was carried out by using Taguchi’s L₉ orthogonal array under different conditions of parameters. The response of SR is considered for improving the machining efficiency. Optimal combination of parameters was obtained Taguchi Optimization technique. The confirmation experiments results shows that the significant improvement in Surface Finish was obtained. ANOVA have been used to analyze the contribution of individual parameters on Surface Roughness. The experimental result demonstrates that the Taguchi method satisfies the practical requirements.

• Periodical: Applied Mechanics and Materials (Volumes 766-767)
• Pages: 867-872
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.766-767.867
• Online since: June 2015
• Authors: P. Sengottuvel*, V. Palanisamy, J. Arun, N.R.R. Anbusagar, J. Hameed Hussain
• Keywords: ANOVA, Electrical Discharge Machine, Surface Roughness, Taguchi Technique

References

[1] Sengottuvel, P., Satishkumar, S. and Dinakaran, D., Optimization of Multiple Characteristics Of EDM Parameters Based on Desirability Approach And Fuzzy Modeling. Journal of Procedia Engineering, 2013, 64, 1069-1078.

DOI: 10.1016/j.proeng.2013.09.185

[2] Sengottuvel, P., Satishkumar, S. and Dinakaran, D., Multi Objective Optimization of Process Parameters During Electrical Discharge Machining of Inconel 718 Using Desirability Approach. International Journal of Applied Mechanics and Materials, 2012, 159, 176-180.

DOI: 10.4028/www.scientific.net/amm.159.176

[3] Sengottuvel, P., Satishkumar, S. and Dinakaran, D., Multi Objective Optimization Technique for EDM of Inconel 718 Alloy. Journal of Artificial Intelligent systems and machine learning, 2011, 3, 853-858.

[4] M.K. das, K. Kumar and T.K. Barman, Optimization of Surface Roughness and MRR using WPCA Elsevier Science Direct Volume 64, 2013, 446-455.

DOI: 10.1016/j.proeng.2013.09.118

[5] Yan, B. H., Huang, F. Y., Chow, H.M., & Tsai, J. Y. (1999).

[6] Adeel Ikram nadeem Ahmad Mufti, Muhammad Qaiser Saleem, parametric Optimization of Surface roughness, Kerf and MRR in WEDM using Taguchi Design of Experiment. International Journal of Advanced manufacturing technology, 2013, 27(7), 2133-2141.

DOI: 10.1007/s12206-013-0526-8

[7] B. Bhattacharyya, S. Gangopadhyay & B.R. Sarkar, Modelling and analysis of EDMed job surface integrity, Journal of materials processing technology, 2007, 189, 169-177.

DOI: 10.1016/j.jmatprotec.2007.01.018

[8] J.Y. kao, C.C. Tsao, S.S. Wang, and C.Y. Hsu, optimization of the EDM parameters on machining Ti-6Al-4V with multiple quality characteristics, International Journal of advanced manufacturing technology, 2010, 47, 395-402.

DOI: 10.1007/s00170-009-2208-3

[9] Logothetis. N & Wynn.H. P, Quality Through design; Experimental design, off – line quality control and Taguchi Contributions, 1989, Oxford: Clarendon Press.

[10] J. Anitha, Raja das and M.K. Pradhan, Optimization of Surface Roughness in EDM for D2 steel by RSM Approach, Universal Journal of Mechanical Engineering, 2014, 2(6), 205-210.

DOI: 10.13189/ujme.2014.020605

[11] Dave, K. V., Patel, D. S., Effect of Tool geometry and Process parameters on Surface roughness and MRR in EDM of Tool Steel, Int J of Engineering Research & Technology (IJERT), July-2012, pp.1-9.

[12] Ahsan Ali Khan, Mohammad Yeakub Ali and Mohafizul Haque, A study of Electrode shape on the performance of die sinking EDM, International Journal of Mechanical and materials Engineering, 4(2009), 19-23.