Wear Modeling of Steel Surfaces to the Flow under Pressure of Melts Polymers with SGF

Abstract:

Consequences of the wear processes at screws and barrels of injection machines and extruders for processing of plastics reinforced with short glass fibers, arise after a longer time (10,000 cycles). Because of this they are working that through appropriate modeling attempts on the profits to be obtained in a short time as much information relating to both the mechanisms of wear and its size, so that the effect can be easily confuted in practice. Starting from the idea that the greatest pressure and velocity of composite melted is in the die nozzle, was an experimental nozzle with wear samples of sizes and weights which can be measured with precision as good. For a larger accuracy of measurements, we used a method for radiometric measuring, extremely accurate. Different nitriding steels have been studied as nitriding treatments, as well as some special steels and alloyed steels. Besides these, there have been preliminary attempts made to describe and checking corrosive action of termoplastelor on metals. This was another way of checking the wear testing of the samples semi-cylindrical wear samples, which served to simulate the wear of the top layer of the barrel and screw. The first results showed that wear increases depending on the increased pressure. One of the findings is that in similar conditions of injection, with the same content of glass fiber, polyamide 6.6 produces a wear greater than polycarbonate. It was also found that increasing the concentration of glass fibres increase the surfaces wear of barrels and screws.

• Periodical: Advanced Materials Research (Volumes 1061-1062)
• Pages: 626-637
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.1061-1062.626
• Online since: December 2014
• Authors: Virgil Florescu*, Lucian Capitanu, Dorin Rus
• Keywords: Experimental Nozzle, Melted Polymers, Modeling, Short Glass Fibres, Steel Surfaces, Thermoplastics, Wear

References

[1] G.M. Bartenev, 1981 V.V. Lavrentiev, Friction and Wear of Polymer, Elsevier, (1981).

[2] J.V. Kraghelski - Trenie i Iznos, Izdat. Maşinostroenie, Moskva, (1968).

[3] W. Cooper, M.S. Grace – Elastomers, J. Polymer Sci., C 12, pp.135-150, (1966).

[4] M.O.W. Richardson, Polymer Engineering Composites, Applied Science Publishers, (1977).

[5] C. Lhymm, R. Light, Effect of Sliding Velocity on Wear Rate of Fibrous Polymer Composites, Wear, 116, p.343, (1987).

DOI: 10.1016/0043-1648(87)90182-7

[6] J. Awrejcewicz, Yu Pyryev, Nonsmouth Dynamics of Cotacting Thermoelastic Bodies, in Advanced Mechanics and Mathematics, 16, Springer Science, (2009).

[7] L. Căpitanu, V. Florescu, M. Baubec. - Transfer Processes by Cyclic Loads on Composite Plastic Materials / Steel Sufaces Contact, The Annual Symposium of Solid Mechanics, Bucharest, 1999, pp.325-342.

[8] H. Dominghaus H. Modellversuche zum Verschleiß in Kunststoffverarbeitungsmaschinen. Kunststoff Rundschau. 18, 8, 1971, 383-389.

[9] W. Knappe, D. Mahler. Modellversuche zum Verschleiß in Kunststoffverarbeitungsmaschinen. Kunststoff Rundschau 19, 2/3, 1972, pp.45-51.

[10] W. Bauer: Verfahren zum Prüfen der Verschleißwirkung von Preßmassen Kunststoffe. (1967). pp.53-55.

[11] W.W. McCandless u. a.: Verschleiβfeste und korrosionbeständige Zylinder und Schnecken für.

[12] Kunststoffmaschinen. Industrie – Anzeiger. 91 (1969), Nr. 25, S. 25-29.

[13] R. Meridies u. a.: Verschleiβ an Schnecken von Spritzgießmaschinen bri der Verarbeitung von Kunststoffen. Plastverarbeiter, 21 (1970), 617-623.

[14] K. Stark. Undersuschungen über den Verschleiß an Metallöberflächen die mit strömended Kunststoffschmeltzen in Berührung stehen. Student – Arbeit am Deuschen Kunststoff – Institut, Darmstadt, (1970).

[15] Capitanu L., Iarovici A., Onişoru J. On polyamide and polycarbonate composite materials behaviour under dry friction. The Annals of University Dunarea de jos, of Galati, Fascicle VIII, Tribology, (2003).

[16] Capitanu L., Onisoru J., Iarovici A. Tribological aspects for injection procerssing of thermoplastic composite materials with glass fiber, Journal of the Balkan Tribological Association, Vol. 11, No. 4, pp.542-557 (2006); ISSN 1310-4772.

[17] Capitanu L., Florescu V. Tribological Aspects of Wear of Polished Steel Surfaces in DrFriction Contact on Polymer Composites with Glass Fibres. American Journal of Materials Science 2013, 3(1): 8-18. DOI: 10. 5923/j. materials. 20130301. 02.

[18] Maranyl Polyamide, Technical Note, Goodfelow Cambridge Ltd., (2012).

[19] Viers Brendt D. (1999). Polymer Data Handbook. Oxford University Press, Inc. p.189. ISBN 978-0195107890.

[20] Material Selection Guide, 1. 888. CURBELL, www. curbellplastics. com.

[21] Lexan, Polycarbonate Resin, General Electric Data Sheet, www. vistatek. com.

[22] Makrolon® polycarbonate product description. Bayer A.G. www. plastics. bayer. com.

[23] Technyl, Rhone Paulenc, https: /www. google. ro/#q =Technyl%2C+Rhone+Paulenc.

[24] Rus D., Capitanu L., Florescu V. About an experimental modeling of steel suface wear in injection of plastic composites with SGF. Proceedings of ACME 2014, Iasi, Romania.

DOI: 10.4028/www.scientific.net/amm.658.365