Investigation on Microstructure and Wear Resistance of the New CrWMoV High-Alloy Wear Resistant Cast Iron

Zheng Ting Wang; Hong Ming Gao

doi:10.4028/www.scientific.net/AMR.1061-1062.670

Paper Titles

Numerical Calculation and Analysis of Water-Lubricated Stern Bearing Considering Elastic Hydrodynamic
p.653

Novel Multi-Stream Plate Exchanger under High Pressure-Structure and its Design Method
p.658

Researches on Lifetime Modeling of LED Luminaires
p.662

Fire Hazard Research of Wire Joint
p.666

Investigation on Microstructure and Wear Resistance of the New CrWMoV High-Alloy Wear Resistant Cast Iron
p.670

Wear Behavior and Microstructural Evolution during Dry Sliding Wear of AZ51 Magnesium Alloy
p.674

A Graphical Symbol for Machining Process Information Description Using Model-Based Definition Technology
p.681

Design and Experimental Analysis of Pepper Fruit Preprocessing Machine
p.687

Design on a Removable Catalyst Muffler
p.692

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 1061-1062Investigation on Microstructure and Wear...

Investigation on Microstructure and Wear Resistance of the New CrWMoV High-Alloy Wear Resistant Cast Iron

Abstract:

This paper mainly introduces the new CrWMoV high-alloy wear resistant cast iron prepared by the composition design, the composition proportion and the melting and pouring, and analyses its microstructure and wear resistance. Microstructures and phases of the new CrWMoV high-alloy wear resistant cast iron were analyzed by scanning electron microscopy, energy dispersive spectrometer and X-ray diffract meter. Furthermore, the Rockwell hardness, impact toughness and wear resistance of the material were also studied. The result show that the composition of the new CrWMoV high-alloy wear resistant cast iron is mainly (V, W) C particles which is synthesized in-situ and evenly distributed in the composite, as well as a small amount of (Cr, Fe) ₇C₃ phase and Fe-Cr phase. The average Rockwell hardness of the composite is about 64.5 HRC, the average impact toughness is 9.85 J/cm², and the relative wear ability of the composite is about 2 times higher than the Cr15Mo2Cu which shows good wear resistance.

You might also be interested in these eBooks

Research in Materials and Manufacturing Technologies IV

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 1061-1062)

Pages:

670-673

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.1061-1062.670

Citation:

Cite this paper

Online since:

December 2014

Authors:

Zheng Ting Wang*, Hong Ming Gao

Keywords:

CrWMoV High-Alloy, Microstructure, Wear Resistance, Wear Resistant Cast Iron

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] D.D. Liu, G.S. Zhang, S.Z. Wei and et al: Investigation of Wear Performance of High Vanadium High Speed Steel [J]. Foundry Technology. 2013, 34(2): 135-137.

Google Scholar

[2] J.X. Gong, D. Li, Y.F. Xiao and et al: Microstructure and wear resistance of Fe-Cr-B-C hardfacing alloys [J]. Transactions of Materials and Heat Treatment. 2010, 31(3): 136-140.

Google Scholar

[3] L.J. Xu, J.D. Xing, S.Z. Wei and et al: Investigation on wear behaviors of high-vanadium high-speed steel compared with high-chromium cast iron under rolling contact condition [J]. Materials Science and Engineering. 2006, 434: 63-67.

DOI: 10.1016/j.msea.2006.07.047

Google Scholar

[4] Z.H. Wang, D.Y. He, C.L. Yu and et al: Effect of vanadium on property of Fe-Cr-C hardfacing alloy [J]. Transactions of the China Welding Institution, 2010, 31(9): 61-63.

Google Scholar