Use of AE Testing Data for Condition Monitoring in Wind Turbine Gearbox

Abstract:

Acoustic emission (AE) method of nondestructive check is based on exertion wave radiation and their registration during fast local material structure reorganization. It is used as a means of analysis of materials, constructions, productions control and diagnosis during operating time. In the article, it is applied to structural health monitoring of Wind Turbine Gearbox (WTG). Acoustic emission testing has been used for years to test metallic structures. More recently it has become the primary method of testing WTG; all are present in the failure of WTG. AE has been very successful at detecting all of these failure mechanisms and sometimes identifying them from amplitude analysis of the AE signals. However in large structures, the high acoustic attenuation in WTG precludes amplitude analysis unless the origin of the individual signals can be identified and corrections for the distances traveled applied to the signal amplitudes. The usual method of testing WTG structures has been to apply an array of sensors spaced so that a moderate amplitude AE signal occurring midway between them will just barely trigger each sensor.

• Periodical: Advanced Materials Research (Volumes 1070-1072)
• Pages: 1893-1897
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.1070-1072.1893
• Online since: December 2014
• Authors: Hong Wu Qin, Fu Cheng Cao, Qin Yin Fan, Maimai Jiang Aishan*
• Keywords: Acoustic Emission, Condition Monitoring, NDT, WTG

References

[1] TOMASZ B, DARIUSZ Z. Application of wavelet analysis to acoustic emission pulses generated by partial discharges [J]. IEEE Transactions on dielectrics and electrical insulation. 2004, 11(3): 433-449.

DOI: 10.1109/tdei.2004.1306722

[2] DING Y, REUBEN R L, STEEL J A. A new waveform method for analysis for estimating AE wave arrival times using wavelet decomposition [J]. NDT&E International, 2004, 37(4): 279-290.

DOI: 10.1016/j.ndteint.2003.10.006

[3] SURGEON M, BUELENS C, WEVERS M, et al. Waveform based analysis techniques for the reliable acoustic emission testing of composite structures. Journal of Acoustic Emission (USA). 2001, (18-19): 34-40.

[4] Q.F. Lu et al., Model of stator inter-turn short circuit fault in doubly-fed induction generators for wind turbine, " in Proceedings of IEEE PESC, 04, vol. 2, pp.932-937, Aachen (Germany), June (2004).

DOI: 10.1109/pesc.2004.1355544

[5] L. Mihet-Popa et al., Condition monitoring of wind generators, " in Proceedings of IEEE IAS, 03, vol. 3, pp.1839-1846, Salt Lake City (USA), October (2003).

[6] S.G.M. Krämer et al., Fiber optic sensor network for lightning impact localization and classification in wind turbines, " in Proceedings of IEEE ICMFIIS, 06, vol. 2, pp.173-178, Heidelberg (Germany), September (2006).

[7] M.E.H. Benbouzid, A review of induction motors signature analysis as a medium for faults detection, IEEE Trans. Industrial Electronics, vol. 47, n°5, p.984–993, October (2000).

DOI: 10.1109/41.873206

[8] D. Casadei et al., Experimental fault characterization of doubly fed induction machines for wind power generation, " in Proceedings of IEEE SPEEDAM, 06, pp.1281-1286, Taormina (Italy), May (2006).

DOI: 10.1109/speedam.2006.1649965

[9] S. G. Taylor, H. Jeong, J. K. Jang, G. Park, K. M. Farinholt, M. D. Todd, and C. M. Ammerman, Full-scale fatigue tests of CX-100 wind turbine blades. Part II: analysis, in SPIE Smart Structures/NDE, San Diego, California, 2012, pp. 83430Q-10.

DOI: 10.1117/12.917497

[10] S. R. Anton, et al., Multi-source energy harvesting for wind turbine structural health monitoring node, presented at the Advances in Structural Health Management andComposite Structures, Jeonju, Korea, (2012).