Effect of Combined Microwave Heating and Impinging Hot-Air on Rubberwood Drying

Abstract:

Applying microwave heating and impinging hot-air is one of the most interesting methods to increase the higher drying rates of rubberwood drying based on acceptable quality. A maximum microwave power level of 200W at a frequency of 2.45GHz with maximum working temperature of 70°C, only hotair (70°C) and combined microwave (200W) - hotair (70°C) were choosed to evaluate the effect of rubberwood drying by different width sizes (1, 2, 3 and 4 in.) by 46 in. length by 1 in. thick. In all cases, the drying time is reduced significantly from 168 h to less than 8-15 h in various wood widths and resulted in saving to an extent of about 91% of drying time from initial moisture content ranges of 73%-49% to 15% percent of moisture level. Drying stresses from prong test no found during drying and total color of rubberwood changed after high temperature drying is a natural surface when compared to fresh wood. The values of six strength compared to the reference values are concentrated in the ranges of 16.9-23.9 (11.0)MPa for shearing strength parallel to grain, 4291.1-6701.6 (4350)N for hardness, 73.3-110.2 (66.0)MPa for MOR, 7059.5-12856.7 (9240.0) MPa for MOE, 27.2-14.3 (5.0)MPa for compressive strength perpendicular to grain and 60.6-35.7 (32.0)MPa for compression strength parallel to grain. These results show that it is possible to develop a drying process for rubberwood using microwave-hot air in investigating further in this area.

• Periodical: Advanced Materials Research (Volumes 538-541)
• Pages: 2413-2416
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.538-541.2413
• Online since: June 2012
• Authors: Nuchtida Promtong, Thanate Ratanawilai, Chayut Nuntadusit
• Keywords: Hot-Air, Mechanical and Physical Properties, Microwave Drying, Rubberwood

References

[1] S. Srivaro, T.Wongprot, N. Matan and B. Kyokong: Songklanakarin J. Sci. Technol., 2008.

[2] R. Yamsaengsung and T. Sattho: submitted to Drying Technology, 26: 798–805, 2008.

DOI: 10.1080/07373930802046518

[3] L.J. Pordage and T.A.G. Langrish: submitted to Drying Technol 17(1-2):237-256, 1999.

[4] G. Du, S. Wang and Z. Cai: Drying Technology, 23: 1–16, (2005)

[5] L. Hansson, A.L. Antti: Journal of Materials Processing Technology 141 (2003) 41–50

[6] N. Terzie:In 4th COST E15 Workshop on Methods for improving drying quality of wood, 2002.

[7] S. Vongpradubchai, P. Rattanadecho: Chemical Engineering and Processing 48 (2009)

[8] A. Treu, H. Rieche and H. Militz: the 39th Annual Meeting Istanbul, Turkey, 25-29 May 2008.

[9] R. Seyfarth, M. Leiker and N. Mollekopf:8th Inter. IUFRO Wood Drying Conference,2003.

[10] M. Zhang, J. Tang, A.S. Mujumdar and S. Wang: Food Science & Technology 17 (2006)

[11] H. H. Nijhuis, H. M.Torringa, S. Muresan, D. Yuksel, C. Leguijt, & W. Kloek: Food Science and Technology, 9, 13-20. (1998)

DOI: 10.1016/s0924-2244(97)00007-1

[12] A. K.Datta, S. S. R.Geedipalli and M. F. Almeida: Food Technology, 59(1), 36–40(2005).

[13] S. Geedipalli, A.K. Datta and V. Rakesh: food and bioproducts processing 86(2008)53–63.

DOI: 10.1016/j.fbp.2007.10.016

[14] G.R. Askari, Z. Emam-Djomeh and S.M. Mousavi: Food Sci.and Tech. International ,2006.

[15] A.Andres, C. Bilbao and P. Fito: Journal of Food Engineering 63 (2004) 71–78

[16] S.Oztekin, T.Erdem and S.Karaaslan: African Journal of Agricultural Research, (2011)

[17] S. Gunasekaran: Drying Technology, 8(5), 1039-1047(1990).

[18] T.N. Tulasidas, G.S.V. Raghavan& E. R.Norris,: Transaction of ASAE, 36, 1861-1865.

[19] D.G. Prabhanjan, H.S. Ramaswamy & G.S.V. Raghavan, Journal of Food Engineering, 1995.

[20] W. Killman and L.T. Hong: Rubberwood – the success of an agricultural by-product, 2000.