Study on the Electrometric Method to Measure the Young’s Modulus of Metal Materials

Abstract:

Young's modulus is one of the basic mechanical properties of materials, so its accurate measurement has great engineering significance. Electrometric method is one of the commonly used method. Proceeding from experimental techniques, this paper studies the key factors which affect the result of the experimental measurement, including the influence of the uneven load, the pre-stretching, the hardening time of the strain gauge binder, and sticking quality of strain gauge; comprehensively provides the experimental measures to improve the measurement accuracy. Then through the uncertainty evaluations of the results with different measures, this paper from a point of quantitative view proves that taking these measures can reduce the dispersion of the measurement results and significantly improve the accuracy of experimental results.

• Periodical: Advanced Materials Research (Volumes 652-654)
• Pages: 1319-1334
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.652-654.1319
• Online since: January 2013
• Authors: Li Feng Xiao, Ran Duan, Xin Guang Chen
• Keywords: Electrometric Method, Uncertainty, Young's Modulus

References

[1] QIAN Liang-cun, HONG Wei-ning, ZHU De-quan, LIU Jia-ju and YE Jian, in: The Research of Young s Elastic Modulus Measurement Accuracy, Mechanical Engineer, no. 7, pp.39-44, (2008).

[2] CHEN Wei-yi, LU Chang-hong, QI Huan, WANG Yan and MENG Fan-bo, in: A comprehensive and researchful experiment project for the measurement of Young's modulus, volume 28 of College Physics, no. 12, pp.54-56, (2009).

[3] ZHOU Xiao-ming, in: A Comparison on Measuring Methods of Young s Modulus in Physics Experimental Teaching, volume 6 of Experiment Science and Technology, no. 9, pp.97-99, (2011).

[4] Bao Yu, Luo Zhi, in: A deviation analysis on the experimental result of Static tensile method to measure the Young's modulus of the metal wire, volume 5 of Physics and Engineering, no. 15, p.61, (2005).

[5] Yi Hui, Zhang Wei, in: Error Due to Transverse Sensitivity in Strain Gages and Its Correction, Helicopter Technique, no. 1, p.60, (2011).

[6] R. C. Jaeger, J. C. Suhling and R. Ramani, in: Errors associated with the design, calibration and application of piezoresistive stress sensors in (100) silicon, volume 14 of IEEE Trans. On Components, Packaging and Manufacturing Technology, no. 1, p.97, (1994).

DOI: 10.1109/96.296437

[7] Li Yan, Li Xin'e, Pei Dongxing, in: Error Analysis of Strain Measurement System, Modern Electronics Technique, no. 24, p.181, (2008).

[8] D. Vyroubal, in: A circuit for lead resistance compensation and complex balancing of the strain-gauge bridge, volume 14 of IEEE Trans. On Instrumentation and measurement, no. 1, p.44, (1993).

DOI: 10.1109/19.206678

[9] Cheng Daxian, in: Handbook of mechanical design, edited by Chemical Industry Press, Beijing(2004), in press.

[10] Xu Jixin, in: Experiment on material mechanics. edited by Northwestern Polytechnical University Press, Xi'an, in press.

[11] Wu Yong-hua, Huo Jian-qing, Xiong Yong-hong, in: The first volume of College physical experiment. edited by High education press, Beijing, in press.

[12] Dai Juan, Wang Da-peng, Chen Lei, Liu mei, in: Sticking techniques of strain gauges in the experiment of electrometric stress, volume 3 of Journal of Hunan Institute of Engineering, vol. 3, no. 13, pp.55-57, (2003).

[13] Sha Ding-guo, in: Error analysis and measurement uncertainty evaluation. Edited by China Metrology Press, Beijing, in press.

[14] Liu Zhimin, in: Uncertainty and practice. edited by China Standards Press, Beijing(2003), in press.

[15] Ye Pei-de, in: Understanding, evaluation and application of measurement uncertainty, edited by China Metrology Press, Beijing(2007), in press.

[16] Li Rong-feng, Cai Yi-xin, Kuang Lan-xian, Tan Bo-cong, in: Analysis of measurement uncertainty of tensile test for square specimen, research on iron and steel. no. 1, p.4, (2004).