Deformation Heating and Its Effect on the Processing Maps of Ti-15-3 Titanium Alloy

Abstract:

In the present study, deformation heating generated by plastic deformation and its effect on the processing maps of Ti-15-3 titanium alloy were investigated. For this purpose, hot compression tests were performed on a Gleeble-3800 thermo-mechanical simulator in the temperature range of 850-1150 °C and strain rate range of 0.001-10 s¹. The temperature rise due to deformation heating was calculated and the as-measured flow curves were corrected for deformation heating. Using the as-measured and corrected flow stress data, the processing maps for Ti-15-3 titanium alloy at a strain of 0.5 were developed on the basis Murty‘s and Babu’s instability criteria. The results show that both the instability maps based the two instability criteria are essentially similar and are characterized by an unstable region occurring at strain rates higher than 0.1 s¹ for almost the entire temperature range tested. The unstable regions are overestimated from the as-measured data due to the effect of deformation heating, indicating a better workability after correcting the effect of deformation heating. This is further conformed by the analysis based on strain rate sensitivity.

• Periodical: Advanced Materials Research (Volumes 712-715)
• Pages: 58-64
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.712-715.58
• Online since: June 2013
• Authors: Jing Qi Zhang, Hong Shuang Di, Xiao Yu Wang
• Keywords: Deformation Heating, Hot Deformation, Processing Map, Titanium Alloy

References

[1] R.L. Goetz and S.L. Semiatin: J. Mater. Eng. Perform. Vol. 10 (2001), p.710

[2] F.A. Slooff, J. Zhou, J. Duszczyk and L. Katgerman: Scripta Mater. Vol. 57 (2007), p.759

[3] J. Castellanos, I. Rieiro, M. Carsí, J. Muňoz, M. El Mehtedi and O.A. Ruano: Mater. Sci. Eng. A Vol. 517 (2009), p.191

[4] A. Laasraoui and J.J. Jonas, Metall. Trans.A Vol. 22 (1991), p.1545

[5] Y. Liu, R. Hu, J.S. Li, H.C. Kou, H.W. Li, H. Chang and H.Z. Fu: Mater. Sci. Eng. A Vol. 497 (2008), p.283

[6] I. Rieiro, V. Gutiérrez, J. Castellanos, M. Carsí, M.T. Larrea and O.A. Ruano: Metall. Mater. Trans. A Vol. 41 (2010), p.2396

DOI: 10.1007/s11661-010-0259-6

[7] B. Wietbrock, W. Xiong, M. Bambach and G. Hirt: Steel Research Int. Vol. 82 (2011), p.63

[8] Y.V.R.K. Prasad and S. Sasidhara: Hot Working Guide: A Compendium of Processing Maps (ASM International, Materials Park, Ohio 1997).

[9] Y.V.R.K. Prasad: J. Mater. Eng. Perform. Vol. 12 (2003), p.638

[10] A. Chiba, S.H. Lee, H. Matsumoto and M. Nnakamura: Mater. Sci. Eng. A Vol. 513-514 (2009), p.286

[11] J. Dzwonczyk and Y.V.R.K. Prasad: Adv. Eng. Mater. Vol. 8 (2006), p.966

[12] Y.P. Li, H. Matsumoto and A. Chiba: Metall. Mater. Trans. A Vol. 40 (2009), p.1203

[13] M. Morakabati, Sh. Kheirandish, M. Aboutalebi, A. KarimiTaheri and S.M. Abbasi: Mater. Sci. Eng. A Vol. 528 (2011), p.5656

[14] M.Q. Li, H.S. Pan, Y.Y. Lin and J. Luo: J. Mater. Process. Technol. Vol. 183 (2007), p.71

[15] S.L. Semiatin and T.R. Bieler: Acta Mater. Vol. 49 (2001), p.3565

[16] Y. Niu, H.L. Hou, M.Q. Li and Z.Q. Li: Mater. Sci. Eng. A Vol. 492 (2008), p.24

[17] H.L. Gegel, in: Proceedings of Symposium on Experimental Verification of Process Models, edited by C.C. Chen, Metals Congress, September 21–23, 1981, Cincinnati, OH, ASM International, Metals Park, Ohio (1983).

[18] S.V.S. Narayana Murty and B. Nageswara Rao: Mater. Sci. Eng. A Vol. 254 (1998), p.76

[19] S.V.S. Narayana Murty and B. Nageswara Rao: Metall. Mater. Trans. A Vol. 28 (1997), p.2170

[20] N.S. Babu, S.B. Tiwari and B. Nageswara Rao: Mater. Sci. Technol. Vol. 21 (2005), p.976

[21] M.C. Mataya and V.E. Sackschewsky: Metall. Mater. Trans. A Vol. 41 (1994), p.2737

[22] F. Montheillet, J.J. Jonas and K.W. Neale: Metall. Trans. A Vol. 27 (1996), p.232

[23] S.V.S. Narayana Murty, B. Nageswara Rao and B. P. Kashyap: Int. Mater. Rev. Vol. 45 (2000), p.15

[24] A. Ahadi, A. Karimi Taheri, K. Karimi Taheri, I.S. Sarraf and S.M. Abbasi: J. Mater. Eng. Perform. Vo. 21 (2012), p.516

DOI: 10.1007/s11665-011-9936-x