The Development of Automatic Girth Welding Machine with Dual-Arm for Automobile Axle

Jin Hu Song

doi:10.4028/www.scientific.net/AMR.779-780.1089

Paper Titles

Port Service Efficiency Model Based on Optimization of Supply Chain Logistics System
p.1066

Study on Analysis and Preventive Measures for Damage of Durability of Reinforced Concrete Bridges
p.1070

Introduction to Rural Road Greening
p.1077

Importance of Road Network Layout and Optimization Methods Based on the Reliability
p.1081

The Development of Automatic Girth Welding Machine with Dual-Arm for Automobile Axle
p.1089

A Design Scheme of the Automatic Obstacle-Avoidance Car
p.1094

Development of Automobile Drive Shaft Automatic Welding Machine
p.1098

The Brake Guards against Holds the Dead (ABS) Teaching Laboratory Bench the Development
p.1102

The Automobile Brake Guards against Holds the Dead (ABS) Laboratory Bench Wheel Hydraulic Pressure Actuation System the Development
p.1106

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 779-780The Development of Automatic Girth Welding Machine...

The Development of Automatic Girth Welding Machine with Dual-Arm for Automobile Axle

Abstract:

In order to solve the problem of automobile rear axlewelding equipment with the low level of automation,the poor accuracy, the poorefficiency, a automatic girth welding machine with dual-arm for automobile axlehas been developed based on PLC. Thewelding Proeess automation is realized by PLC controlling gun movement. Theautomatic welding machine has the characteristics of high control precision,good security, fast response speed, high degree of automation, improving weldingquality and production effieiency, lowed serap rates, eonvenient operation, easymaintenance, in particular to improve the working eonditions of workers and improveproduetion effieieney has obvious praetical signifieanee.

You might also be interested in these eBooks

Materials, Transportation and Environmental Engineering

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 779-780)

Pages:

1089-1093

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.779-780.1089

Citation:

Cite this paper

Online since:

September 2013

Authors:

Jin Hu Song

Keywords:

Automatic Welding Machine, Automobile Axle, Programmable Logic Controller (PLC)

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Youde Zhang, Zhiying Zhao, Principle, application and experiments of single chip microcomputer, Fudan University Press, Shanghai, (2000).

Google Scholar

[2] Kun Ding, Hua Qiu, J Shinong ing, Application of single chip computer system for all position welding, Electric Welding Machine, 8 (2002).

Google Scholar

[3] Jinbai Zhang, Xiaoguang, Li yu Wu,. The anti-interference research of the system of tig control, Journal of Wuhan University of Science and Engineering, 2 (2010).

Google Scholar

[4] Guangdong Chen, Principle and interface technology of single chip microcomputer, Huazhong University of Science and Technology Press, Wuhan, (1999).

Google Scholar

[5] Zhengjun Liu: Research of Circular Seam Welding Equipment for Automobile Rear Axle House, Hot Working Technology, 11(2007).

Google Scholar

[6] Haochun Liu: Design of the Automatic Welding Machine Lift Control System Based on PLC, Journal of Wuhan University of Technology, 12(2007).

Google Scholar

[7] Aihua Zhang: All-Position Automatic Welding Systems Based on SCM and Welding Velocity Control, Electrical Automation, 4 (2010).

Google Scholar