The Chip in the Up and Down Milling Process

Veronika Fečová; Peter Michalik; Jozef Zajac; Jozef Mihok; Jozef Berthoty

doi:10.4028/www.scientific.net/AMR.856.379

Paper Titles

The Effect of Mixing Coal with Biomass in Solid Fuel Briquettes
p.338

Prediction of the Remaining Service Life of Superheater and Reheater Tubes in Coal-Biomass Fired Power Plants
p.343

Study on the Performance of the Organic Rankine Cycle System with Internal Heat Exchanger under Vehicle Engine Various Operating Conditions
p.349

Current Mode Filters Using Current Feedback Amplifiers with Negative Impedance (Resistance)
p.359

VPP Processed Variable Phase Controller for Array Antenna Scanning
p.364

Numerical Simulation of the Mechanical Structure of a Helmet Motorcyclist
p.368

The Stress Field in a Flexed Beam with an Elastoviscoplastic Behavior
p.373

The Chip in the Up and Down Milling Process
p.379

Creep Behavior of Catheter Reinforced with Braids: Analytical Simulation of Uniaxial Tension under Two-Stage Step Stress
p.384

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 856The Chip in the Up and Down Milling Process

The Chip in the Up and Down Milling Process

Abstract:

The milling is the most used technology in engineering. The shape of chip is important for its transport and for economical aspect of this technology. The volumetric coefficient of chip represents the shape of chip. The small chip has a lower volumetric coefficient, but the very small chip is not very desired in the machining, because it can damage the machine. The main aim of this contribution was monitoring of chip in the milling process by high-speed camera and consequently the evaluation of this chip by the volumetric coefficient of chip. This coefficient was monitoring in the peripheral up and down milling with the different radial cutting depth.

You might also be interested in these eBooks

Material Science and Engineering Technology II

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 856)

Pages:

379-383

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.856.379

Citation:

Cite this paper

Online since:

December 2013

Authors:

Veronika Fečová, Peter Michalik, Jozef Zajac, Jozef Mihok, Jozef Berthoty

Keywords:

Chip, Milling Process, Volumetric Coefficient of Chip

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] A. Janáč, et al.: Technológia obrábania, Bratislava: Slovenská technická univerzita v Bratislave (2004) . p.289.

Google Scholar

[2] J. Mádl, et al.: Technologie obrábění – 1. Díl, České vysoké učení technické v Praze. Fakulta strojní, p.79, http: /www. strojar. com/upload/skripta/Technologie_obrabeni_1. pdf.

DOI: 10.14311/bk.9788001071397

Google Scholar

[3] M. Neslušan, M., Čilliková: Teória obrábania, Žilina: Zilinská univerzita v Žiline (2007), p.167.

Google Scholar

[4] K. Vasilko: Analytická teória trieskového obrábania, Prešov: Fakulta výrobných technológií TU v Košiciach so sídlom v Prešove (2007), p.481.

Google Scholar

[5] G. Fedorko et al: Vplyv obsahu Ni a Cr na mechanické vlastnosti Hadfieldovej ocele. In: Metal 2011, Brno, (2011), pp.1-6.

Google Scholar

[6] Z. Hutyrova, J. Zajac: Turning of composite material with organic reinforcement (wood plastic composite)", Advanced Science Letters, Volume 19, Issue 3 (2013), pp.877-880.

DOI: 10.1166/asl.2013.4850

Google Scholar

[7] J. Novak-Marcincin, M. Janak, L. Novakova-Marcincinova, V. Fecova: Possibility of quick check on milling strategy suitability, In: Tehnički Vjesnik. Vol. 19, no. 4 (2012), pp.959-964.

DOI: 10.1063/1.4707641

Google Scholar

[8] J. Duplak, I. Orlovsky, M. Cuma: Comprehensive expression of durability for the selected cutting tools in comparison with standard ISO 3685, In: Advanced Science Letters. Volume 19, Issue 2, (2013), pp.460-463.

DOI: 10.1166/asl.2013.4745

Google Scholar

[9] P. Monka: The Comparison of Surface Roughness Characteristics Achieved by the Machining with Conventional and Unconventional Geometry of Tools, In: Advanced Materials Research. Vol. 622-623 (2012), pp.352-356.

DOI: 10.4028/www.scientific.net/amr.622-623.352

Google Scholar

[10] Z. Somsakova: Štúdium WPC, In: Deň mladých technológov 2010 : YTD 2010: Prešov (2010), pp.107-112.

Google Scholar

[11] K. Monkova, S. Hloch: The dependency of the tool life on the cutting speed at the investigation of the tool with specific geometry, In: Advanced Materials Research, Volume 622, (2013), pp.347-351.

DOI: 10.4028/www.scientific.net/amr.622-623.347

Google Scholar

[12] N. Ungureanu, M. Ungureanu, M. Hatala: Estimation of Reliability of Equipment, In: Scientific Bulletin : Fascicle: Mechanics, Tribology, Machine Manufacturing Technology. Vol. 2012, no. 26 (2012), pp.76-79.

Google Scholar