For Libraries For Publication Open Access Downloads About Us Contact Us
Paper Titles
Simulation of Stress Intensity Factor and J-Integral on UIC 54 Railway Failure Using A Fracture Mechanics Approach
p.1
The Behavior of Thin-Walled Cylinders with Ribs Regarding the Energy Absorption Capability on High-Velocity Impact
p.9
Topology Optimization of Motorbike Footsteps Using Finite Element Method
p.19
Analytical Prediction of Crushing Thin-Walled Square Tube with Static Axial Loads Using Elliptical Holes as Crush Initiators
p.29
A Bibliometric Analysis of Suspension System Development for Enhancing Comfort in Family Passenger Vehicles
p.43
Muffler Design for Noise Reduction and Pressure Loss Optimization Using Multiobjective Genetic Algorithm
p.63
Development of Savonius Rotor Based on Bezier Curve for Vertical Axis Marine Current Turbine at Sunda Strait, Hindia Ocean
p.69
The Effect of Deflector Angle on the Performance of Turbine Combination Darrieus-Savonius
p.75
Minimizing Conditional Mean Tardiness and Mean Earliness on a Single Machine with the due Windows Approach
p.83

Topology Optimization of Motorbike Footsteps Using Finite Element Method

Article Preview

Abstract:

Footsteps are a foothold for motorbike riders and passengers; they also play a role in maintaining stability when driving. Footsteps must have a solid and lightweight material to support the load from the feet and body of the rider and passengers. In this study, the footstep with the material made from the waste drum brake shoe varied by reducing mass through the static structural simulation process and topology optimization process using Ansys Workbench to get optimal mass, total deformation, equivalent stress, maximum principal stress, and safety factor from each variation. The footstep geometry will be subjected to a load of 1000N and provided with the necessary support. Based on the data obtained during this study, the initial footstep geometry produces data in the form of total deformation (1.383 mm), equivalent stress (21.013 MPa), and safety factor (1.227). The 10% variation produces data in the form of total deformation (1.4368 mm), equivalent stress (20,564 MPa), ,and safety factor ( 1.2538). The 20% variation yields data in the form of total deformation (0.98037 mm), equivalent stress (18.111 MPa), maximum principal stress (18.41 MPa), and safety factor (yield strength: 1.4236,. At the same time, the 25% variation produces data in the form of total deformation (1.3058 mm), equivalent stress (22.27 MPa), and safety factor (1.1577).

By email View Pdf
You have full access to the following eBook
Engineering Innovations Vol. 11 Read eBook
You might also be interested in these eBooks
The 3rd International Conference on Mechanical Engineering Research and Application View Preview

Info:

Periodical:

Engineering Innovations (Volume 11)

Pages:

19-27

DOI:

https://doi.org/10.4028/p-8EHMyY

Citation:

Cite this paper

Online since:

June 2024

Authors:

I Made Gatot Karohika*, Januar Teguh Prasetyo, I Made Parwata, I Nyoman Gde Antara, I Nyoman Budiarsa

Keywords:

Finite Element, Footstep, Optimization, Topology, Waste

Export:

RIS, BibTeX

Permissions:

Creative Commons CC BY 4.0

Share:

Citation:

* - Corresponding Author

References

[1] Association Of Indonesia Motorcycle Industry, "Association Of Indonesia Motorcycle Industry," Association Of Indonesia Motorcycle Industry. Accessed: Sep. 25, 2023. [Online]. Available: Https://Www.Aisi.Or.Id/Statistic/

Google Scholar

[2] "SIPSN - Sistem Informasi Pengelolaan Sampah Nasional", Accessed: Sep. 23, 2023. [Online]. Available: https://sipsn.menlhk.go.id/sipsn/public/data/komposisi

Google Scholar

[3] I. N. G. Antara, K. G. Made, and G. Ketut, "Application of sand casting to recycle aluminum alloy for motorcycle brake handle," in Key Engineering Materials, 2016.

DOI: 10.4028/www.scientific.net/KEM.705.357

Google Scholar

[4] I. M. G. Karohika and I. N. G. Antara, "The utilization of aluminum alloy waste as a footrests support for motorcycle," 2023, p.040017.

DOI: 10.1063/5.0115571

Google Scholar

[5] D. Nurhadiyanto, S. Haruyama, K. Kaminishi, I. M. Gatot Karohika, and D. Mujiyono, "Contact Stress and Contact Width Analysis of Corrugated Metal Gasket," Applied Mechanics and Materials, vol. 799–800, p.765–769, 2015.

DOI: 10.4028/www.scientific.net/amm.799-800.765

Google Scholar

[6] I. M. G. Karohika and S. Haruyama, "Analysis of three-layer gasket performance affected by flange surface," EUREKA: Physics and Engineering, no. 4, p.57–66, Jul. 2022.

DOI: 10.21303/2461-4262.2022.002290

Google Scholar

[7] I. N. Budiarsa, I. N. G. Antara, I. M. G. Karohika, I. W. Widhiada, and N. L. Watiniasih, "Identification Plastic Properties of Spot Welded Joints Using the Instrumented Indentation Technique," IOP Conf Ser Mater Sci Eng, vol. 811, no. 1, 2020.

DOI: 10.1088/1757-899X/811/1/012020

Google Scholar

[8] W. Widhiada, I. M. Widiyarta, I. N. G. Antara, I. N. Budiarsa, and I. M. G. Karohika, "Remote Pressure Water Valve Control System Based on PLC," Int J Adv Sci Eng Inf Technol, vol. 11, no. 3, p.981–986, 2021.

DOI: 10.18517/ijaseit.11.3.14486

Google Scholar

[9] I. M. G. Karohika, S. Haruyama, I. N. G. Antara, I. N. Budiarsa, and I. M. D. B. Penindra, "Sealing Performance Layered Metal Gasket Based on the Simulation Method," Teknik, vol. 41, no. 1, p.14–19, 2020.

DOI: 10.14710/teknik.v41i1.26125

Google Scholar

[10] I. M. G. Karohika and I. N. G. Antara, "The metal gasket sealing performance of bolted flanged with fem analysis," in IOP Conference Series: Materials Science and Engineering, 2019.

DOI: 10.1088/1757-899X/539/1/012018

Google Scholar

[11] W. Widhiada, I. N. G. Antara, I. N. Budiarsa, and I. M. G. Karohika, "The Robust PID Control System of Temperature Stability and Humidity on Infant Incubator Based on Arduino at Mega 2560," in IOP Conference Series: Earth and Environmental Science, 2019.

DOI: 10.1088/1755-1315/248/1/012046

Google Scholar

[12] I. M. G. Karohika and I. N. G. Antara, "Gasket Process Parameter in Metal Forming," in IOP Conference Series: Earth and Environmental Science, 2019.

DOI: 10.1088/1755-1315/248/1/012044

Google Scholar

[13] I. N. Budiarsa, I. N. G. Antara, and I. M. G. Karohika, "Indentation Size Effect of the Vickers Indentation to Improve the Accuracy of Inverse Materials Properties Modelling Based on Hardness Value," in IOP Conference Series: Earth and Environmental Science, 2019.

DOI: 10.1088/1755-1315/248/1/012009

Google Scholar

[14] I. M. G. Karohika, I. N. G. Antara, and I. M. D. Budiana, "Influence of dies type for gasket forming shape," in IOP Conference Series: Materials Science and Engineering, 2019.

DOI: 10.1088/1757-899X/539/1/012019

Google Scholar

[15] I. M. G. Karohika and I. N. G. Antara, "Proses Pembentukan Gasket berlapis dengan Metode Elemen Hingga," Jurnal Energi Dan Manufaktur, 2018.

DOI: 10.24843/jem.2018.v11.i02.p06

Google Scholar

[16] Dzikri Amali Musyaffa, Moch. Agus Choiron, Yudy Surya Irawan, Nafisah Arina Hidayati, Taryono Taryono, "Computer Simulation Investigation Of Crash Box Design As Safety-Protection Technology For Indonesia High-Speed Train", International Journal of Mechanical Engineering Technologies and Application, vol. 4, No. 1, pp.97-103, 2023.

DOI: 10.21776/MECHTA.2023.004.01.11

Google Scholar

[17] Fauzan Aulia, Achmad As'ad Sonief, Nafisah Arina Hidayati, Sanjay M R," Stress Distribution Analysis On Ligament Augmentation And Reconstruction System (Lars) Using Finite Element Method (FEM)", International Journal of Mechanical Engineering Technologies and Application, vol. 4, No. 1, pp.61-68, 2023.

DOI: 10.21776/MECHTA.2023.004.01.7

Google Scholar

[18] I. M. G. Karohika et al., "An Approach to Optimize the Corrugated Metal Gasket Design Using Taguchi Method," Int J Adv Sci Eng Inf Technol, vol. 10, no. 6, p.2435–2440, 2020.

DOI: 10.18517/ijaseit.10.6.12992

Google Scholar

[19] I. N. Budiarsa, I. M. Astika, I. N. G. Antara, and I. M. G. Karohika, "Optimization on strength spot welding joint trough finite element modeling indentation approach," IOP Conf Ser Mater Sci Eng, vol. 539, no. 1, 2019.

DOI: 10.1088/1757-899X/539/1/012042

Google Scholar

© 2025 Trans Tech Publications Ltd. All rights are reserved, including those for text and data mining, AI training, and similar technologies. For open access content, terms of the Creative Commons licensing CC-BY are applied.
Scientific.Net is a registered trademark of Trans Tech Publications Ltd.