Development of Finite Element Analysis Model for Plug Mill Rolling

Abstract:

In the seamless pipe rolling process, the pipe wall thickness is largely determined at the mandrel mill or plug mill. It is possible to obtain the target thickness at these mills by defining the gap of a grooved roll and an inside tool such as a plug. However, the thickness of the free deformation part, which is not in contact with the roll and tool, had generally been estimated by experimental techniques. Although a number of analytical studies of mandrel mill rolling had been reported, few reports had examined plug mill rolling. Therefore, in this research, a finite element analysis model for plug mill rolling was developed by extending the rigid plasticity finite element model "Computational Rolling Mill (CORMILL)." Good agreement between the calculated results and experimental results was obtained for the wall thickness, and it was found that the thickness of the flange part decreases with reduction of the wall thickness at the grooved bottom. These results suggested that the wall thickness distribution of rolled pipes can be controlled by using a suitable inside tool and roll shape in each rolling pass, and the necessary shapes can be obtained by using the newly-developed model.

• Periodical: Key Engineering Materials (Volumes 622-623)
• Pages: 899-904
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.622-623.899
• Online since: September 2014
• Authors: T. Katsumura*, Kazutoshi Ishikawa, Atsushi Matsumoto, Shunsuke Sasaki, Yasushi Kato, Jun Yanagimoto
• Keywords: Rolling , Finite Element Analysis (FEA), Flow Stress, Grooved Roll, Plug Mill, Rigid Plasticity, Seamless Pipe, Wall Thickness

References

[1] A. Ghiotti, S. Fanini, S. Bruschi, P.F. Bariani, Modelling of the Mannesmann effect, CIRP Ann. Manuf. Technol., 58 (2009), 255-258.

DOI: 10.1016/j.cirp.2009.03.099

[2] A. Krux, M. Zemko, FEM-modelling of Barrel-type Cross-roll Piercing and Analysis of the Rotational Motion of the Plug Bar, Steel Res. Int., ICTP2011 Special Edition(2011).

[3] T. Hirakawa, Y. Mihara, M. Kamata, S. Akita, M. Numano, Theoretical Analysis on Mandrel Rolling, The 3rd Int. Conf. on Steel Rolling, 231-238(1985).

[4] S. Yamamoto, S. Tamura, Y. Wada, K. Hamauzu, Modeling of cross-sectional shape of rolled tube and forward slip ratio for single stand rolling of Mandrel Mill, Simul. Mater. Proc. Theory Method Appl. 1998(Int. Conf. Num. Industrial Form. Proc. (6th), 707-713 (1998).

[5] V. Palma, S. Bandini, J. H. Pehle, P. Thieven, The PQF Mill (Premium Quality Finishing Mill)-The Ultimate Process for High Quality Seamless Tube Production, Mech. Work Steel Proc., 37(1999), 585-595.

[6] K. Hori, M. Yamada, Comparison of rolling characteristic between 2-roll mandrel mill and 3-roll mandrel mill, CAMP-ISIJ, 11-2(1998), 344. (in Japanese).

[7] Yan Zesheng, Zhuang Gang, Sun Qiang, New Manufacuturing Technique on Seamless Tube Rolling, The 10th Int. Conf. on Steel Rolling, 1405-1409(2010).

[8] J. Yanagimoto, Y. Kadomura, T. Muto and K. Inoue, Strategic CAE System for the Design of Calibers in the Rolling of Complex Sections, Steel Research, 73-12(2002), 526-530.

DOI: 10.1002/srin.200200023

[9] Edited by The Iron and Steel Institute of Japan, Handbook of Iron and Steel 3rd edition Chap. 11, Maruzen (1980), Tokyo, 958. (in Japanese).

[10] H. Abe, K. Nakagawa, T. Imae, A. Ejima, Material deformation and characteristics of rolling load in plug mill rolling for seamless pipe, Proc. the 1981 Jap. Spring Conf. Technol. of Plasticity (1981), 233-236 (in Japanese).

[11] T. Okui, M. Yamada, T. Yamada, Deformation Analysis of a Three-Roll Reducing Mill, J. Jap. Soc. Technol. Plasticity, 38-432(1997-1), 76-80. (in Japanese).