Reuse of Waste from the South West of England in Alkali-Activated Cement Concrete

Abstract:

The extraction of china clay in the South West of the UK generates waste in a mass ratio of 1:9 for china clay: waste. Currently, part of the coarser waste, “stent” and sand named “china clay sand” (CCS) in this study, is used as building stone or secondary aggregate in concrete and asphalt but the finest waste fraction, called “mica” waste, is used only for the restoration of old quarries. Looking for innovative solutions for the needs of a new Eco-town in the UK, and with regard to uses commercially applicable to construction and of low environmental impact, the china clay waste is being studied as an aggregate in alkali-activated cements (AAC). Aiming to replace primary aggregates with wastes in low risk construction materials, a series of AAC concrete based on a 50% GGBS and 50% fly ash (FA) blend and an equivalent Portland concrete series were produced. In the mixes the primary aggregate was steadily replaced by forms of the waste and tests in compression showed a decreasing trend in strength accordingly. The two series of concrete follow approximately the same ratios of decrease although in absolute values the AAC series reached higher range of strengths on the 28 day compared to the Portland series. While the use of CCS did not have any negative impact, the addition of mica decreased the strength up to 25% more.

• Periodical: Key Engineering Materials (Volumes 629-630)
• Pages: 449-454
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.629-630.449
• Online since: October 2014
• Authors: Adamantia Zografou*, Andrew Heath, Peter Walker
• Keywords: Aggregate, Alkali-Activated, Concrete Strength, Waste

References

[1] T. Blide, T.J. Brown and S.F. Hobbs: United Kingdom Minerals Yearbook 2012. British Geological Survey Open Report, OR/13/024, (2013).

[2] C. Thurlow: China clay from Cornwall and Devon - The modern china clay industry, 4th ed., St Austell, UK (2005).

[3] M. Winter: Case Study - Construction of the A30 Bodmin, HTRL 404(387) report of the Highways Agency (2012).

[4] B. Marsh: The Institute of Concrete Technology -Yearbook 2006-2007, (2007) pp.45-55.

[5] Olympic Delivery Authority, Sustainable design and construction update, ODA 2009/295 (2009).

[6] Information on http: /aggregain. wrap. org. uk/case_studies/2676_use_of_chin. html.

[7] I. Sims and B. Brown in: Concrete Aggregates, edited by P.C. Hewlett, chapter 16 of Lea's Chemistry of Cement and Concrete (Fourth Edition, Butterworth-Heinemann (2003).

[8] P.G. Fookes and W.A. Revie: Concrete (Journal of the Concrete Society), Vol. 16(3) (1982) pp.12-16.

[9] J. Dewar, in: Effect of mica in the fine aggregate on the water requirement and strength of concrete, Cement and Concrete Association, Technical Report TRA/370, Slough, UK (1963).

[10] IPCC, Climate Change 2007: Mitigation. Contribution of Working Group III to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change, edited by B. Metz, O.R. Davidson, P.R. Bosch, R. Dave, L.A. Meyer, Cambridge University Press, Cambridge, UK (2007).

DOI: 10.1017/cbo9781107415416

[11] A. Zografou, A. Heath and P. Walker: China clay waste as aggregate in alkali-activated cement mortars, accepted for publication in ICE Construction Materials, DOI: 10. 1680/coma. 13. 00037 (2014).

DOI: 10.1680/coma.13.00037

[12] A.Á.B. Maia, R.S. Angélica, R. de Freitas Neves, H. Pöllmann, C. Straub, K. Saalwächter: Applied Clay Science, Vol. 87 (2014) pp.189-196.

DOI: 10.1016/j.clay.2013.10.028

[13] K. Gomes, B. Rocha, D. Ferreira, E. Lira, S. Torres, S. De Barros, N. Barbosa: Key Engineering Materials, Vol. 517 (2012) pp.622-627.

DOI: 10.4028/www.scientific.net/kem.517.622

[14] D. Ferreira, B. Rocha, E. Lira, K. Gomes, S. Torres, N. Barbosa: Key Engineering Materials Vol. 517 (2012) pp.617-621.

[15] D.C. Teychenné, R.E. Franklin and H.C. Erntroy: Design of normal concrete mixes, 2nd ed. by B. Marsh, Building Research Establishment (1997).

[16] BSI, BS EN 12350-2 Testing fresh concrete. Slump-test (2009).

[17] BSI, BS EN 206 Concrete. Specification, performance, production and conformity (2013).

[18] BSI, BS 1881-125: 2013 Testing concrete. Methods for mixing and sampling fresh concrete in the laboratory (2013).