Comprehensive Durability Identification of Ceramic Cutting Materials in Machining Process of Steel 80MoCrV4016

Abstract:

Specification cutting tools durability made of cutting ceramic in machining process of steel 80MoCrV4016 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 80MoCrV4016 is most commonly used for production of bearings. Durability of cutting tool defines lifetime of this cutting tool and it determines its suitability for select technological operation. Especially for cutting ceramic is necessary to define durability dependence on available set of cutting speeds and to determine lifetime of tools made of cutting ceramic. Technical science defines a lot of different factors, that they may be cause of shorter cutting tool lifetime. For increase cutting tool durability is necessary maximally possible elimination of these factors. Determination of cutting tool durability is very important, because provides comprehensive information how to determine appropriate technological conditions for selected cutting tool. In engineering is for determination of cutting tools durability used T-v_c dependence. The article describes process how to create durability dependence for cutting tools made of cutting ceramic by means of T-v_c dependence in machining process of steel 80MoCrV4016.

• Periodical: Key Engineering Materials (Volume 669)
• Pages: 286-293
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.669.286
• Online since: October 2015
• Authors: Anton Panda*, Ján Duplák, Miroslav Kormoš, Juraj Ružbarský
• Keywords: Bearings, Cutting Ceramic, Cutting Speed, Durability

References

[1] A.H. Youssef, H. El-Hofy, Machining Technology: Machine Tools and Operations, CRC Press, (2008).

DOI: 10.1201/9781420043402

[2] A. Panda et al., Accompanying phenomena in the cutting zone machinability during turning of stainless steels, International Journal of Machining and Machinability of Materials 5/4 (2009) 383-400.

DOI: 10.1504/ijmmm.2009.026899

[3] E. Isakov, Cutting Data for turning of steel, Industrial Press, New York, (2009).

[4] E.D. Whitney, Ceramic Cutting Tools, William Andrew Publishing/Noyes, (1994).

[5] H. Tschätsch, Applied Machining Technology, Vieweg, Wiesbaden, (2007).

[6] J. Duplák, T-vc dependence for cutting ceramic in standard ISO 3685, Manufacturing Engineering 9/4 (2010) 58-62.

[7] J. Duplák, Verification of T-vc dependence for standard ISO 3685, in: Progressive technologies of machining: Papers of center of progressive technologies 2010, Prešov, FVT TU, pp.45-52.

[8] J. Duplák, M. Hatala et. al, T-Vc Dependence for sintered metal in standard ISO 3685, Technological Engineering 7/2 (2010) 6-9.

[9] J.R. Davis, Materials: ASM Specialty Handbook, ASM International, Ohio, (1998).

[10] J. Mihok, J. Markovič, Importance of planning as a core function of strategic management, Management of Companies (Manažment podnikov) 3/2 (2013) 57-58.

[11] J. Zajac et al, Cutting facilities of new type of came cutting material, in: Proceedings of the Conference PPTO, Košice, 1995, pp.138-139.

[12] K. Vasilko, Analytical theory of splinter machining, FMT TUKE, Prešov, (2007).

[13] R. Cep et al, Surface roughness after machining and influence of feed rate on process, Key Engineering Materials 581 (2014) 341-347.

[14] M. Zelenak et al, Comparison of mechanical properties of surface layers with use of nanoindentation and microindentation tests, Metalurgija 51/3 (2012) 309-312.

[15] Standard STN ISO 3685: Tool-life testing with single-point turning tools, (1999).

[16] T. Krenický, Non-contact Study of Surfaces Created Using the AWJ Technology, Manufacturing Technology 15/1 (2015) 61-64.

DOI: 10.21062/ujep/x.2015/a/1213-2489/mt/15/1/61

[17] T. Zaborowski, Eco-production (Ekowytwarzanie), IBEN, Gorzów Wlkp, 2007 (in Polish).

[18] I. Mrkvica, M. Janoš, P. Sysel, Contribution to milling of materials on Ni base, Applied Mechanics and Materials 217-219 (2012) 2056-(2059).

DOI: 10.4028/www.scientific.net/amm.217-219.2056

[19] T. Krenický, P. Jacko, Simultaneous temperature monitoring using virtualization, in: Scientific Papers: Operation and diagnostics of machines and production systems operational states. Lüdenscheid: RAM-Verlag, 2009, pp.58-62.