Influence of the Cobalt Additive on the Flux Cored Wire of System Fe-C-Si-Mn-Cr-Ni-Mo-V

Abstract:

Studied the effect of the introduction of cobalt into the charge powder fused wire system Fe-C-Si-Mn-Cr-Ni-Mo-V, used in cladding assemblies and equipment parts and mechanisms operating under abrasive and abrasive shock loads., the samples cored wires were manufactured in the laboratory conditions using appropriate powder materials and as a carbonfluoride contained material were used the dust from gas purification of aluminum production.

• Periodical: Key Engineering Materials (Volume 736)
• Pages: 63-67
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.736.63
• Online since: June 2017
• Authors: I.V. Osetkovskiy*, N.A. Kozyrev, A.I. Gusev, O.A. Kozyreva, R.A. Gizatulin, A.V. Valueva
• Keywords: Abrasive Shock Loads, Dependencies, Hardness, Multivariate Analysis, Non-Metalic Inclusions, Recovering, Surfacing, Wear Resistance, Wire

References

[1] P.F. Mendez, N. Barnes, K. Bell, S.D. Borle, S.S. Gajapathi, S.D. Guest, H. Izadi, A.K. Gol, G. Wood, Welding processes for wear resistant overlays, J. Journal of Manufacturing Processes. 16 (2014) 4-25.

DOI: 10.1016/j.jmapro.2013.06.011

[2] V.L. Malinov, Researching by methods of regression analysis wear resistance dependences in abrasive and abrasive-shock wear conditions from chemical composition of deposited metal based on Fe-Cr-Mn-V-C, J. Bulletin of Priazovski Technical University. 2 (2011).

[3] R.T. Foley, M.B. Peterson, C. Zapf, Frictional characteristics of cobalt, nickel, and iron as influenced by their surface oxide films, J. A S L E Transactions. 6 (1963) 29 – 39.

DOI: 10.1080/05698196308971996

[4] A.I. Gusev, I.V. Osetkovskiy, Studying properties of metal deposited by powder wire of system C-Mn-Si-Cr-V-Mo-Со, Progressive technologies and economic in mechanical engineering: Works collection of VII National Scientific-Practical conference for students and young students in 2 volumes. Vol. 1. Yurga Technological Institute. Publishing of Tomsk Polytechnic University, (2016).

[5] I.V. Osetkovskiy, A.I. Gusev, Studying properties of metal deposited by powder wire of system C-Si-Mn-Cr-Mo-Ni-V Progressive technologies and economic in mechanical engineering: Works collection of VII National Scientific-Practical conference for students and young students in 2 volumes. Vol. 1. Yurga Technological Institute. Publishing of Tomsk Polytechnic University, (2016).

DOI: 10.4028/www.scientific.net/kem.736.23

[6] R.A. Gizatulin, N.A. Kozyrev, D.V. Valuev, A.V. Valueva, A. Serikbol, Research on operational characteristics of imported rails under conditions of east siberian railway, J. IOP Conference Series: Materials Science and Engineering. 127 (2016) 1-7.

DOI: 10.1088/1757-899x/127/1/012037

[7] G.V. Galevsky , V.V. Rudneva, S.G. Galevsky, D. P . Iljyashchenko, D.S. Kartsev, Nanosized Borides and carbides for electroplating. Metal-matrix coatings: specifications, performance evaluation, J. IOP Conference Series: Materials Science and Engineering. 125 (2016).

DOI: 10.1088/1757-899x/125/1/012032

[8] Y.N. Saraev, D.A. Chinakhov, D.P. Iljyashchenko, A.S. Kiselev, A.S. Gordynets, I.V. Raev, Study of the stability of electrode metal melting and transfer in the process of consumable electrode welding powered by supplies with differing dynamic characteristics, J. AIP Conference Proceedings. 1783 (2016).

DOI: 10.1063/1.4966490