Paper Titles

Contact Stresses during Roller Rolling of Heat-Exchange Tubes
p.55

Application of Combined Processing Methods for High-Tech Products Manufacturing
p.61

Development of Technology for Producing Holes in Parts with Unpredictable Surface Fluctuations
p.67

Welding Mode Justification for a T-Joint
p.73

Use of Hidden Phase Transfer Heat for Temperature Stabilization in Technological Cutting Systems
p.82

Influence of Processing Modes on the Distribution of Wall Thickness during Cell Formation
p.88

Researching of the Influence of the Cutting Parameters of Expanded Polystyrene with a Thermal Tool on the Form Errors of the Product
p.97

Determination of the Optimal Temperature for Processing Styrofoam with a Thermo-Tool
p.103

Study on the Ultrasonic Vibration Impact on the Performance of Taps when Thread Cutting in Workpieces Made of Difficult-to-Machine Materials
p.109

HomeKey Engineering MaterialsKey Engineering Materials Vol. 910Use of Hidden Phase Transfer Heat for Temperature...

Use of Hidden Phase Transfer Heat for Temperature Stabilization in Technological Cutting Systems

Article Preview

Abstract:

This paper describes a temperature stabilization method in dry metal cutting. Using a hidden phase transfer heat allows to significantly reduce the wear rate. The tool holder design with porous evaporative cooling system is presented. Dependences of tool life of cutters on the cutting speed without cooling and with porous cooling are shown. This approach could be advantageous for the cutting of hard materials (titanium alloy).

You might also be interested in these eBooks

Modern Trends in Materials Processing

Info:

Periodical:

Key Engineering Materials (Volume 910)

Pages:

82-87

DOI:

https://doi.org/10.4028/p-wxo6lq

Citation:

Cite this paper

Online since:

February 2022

Authors:

Dmitry Yu. Dubrov*

Keywords:

Dry Cutting, Internal Cooling, Titanium Alloys, Tool Holder Design, Tool Life

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2022 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

[1] Pankin A.V. Processing of metals by cutting, M.: Mashgiz Publ., 1961, 522 p.

[2] Bobrov V.F. Fundamentals of metal cutting. M., Mashinostroyenie Publ., 1975, 344 p.

[3] Shabashov S.P. Investigation of wear resistance of hard alloys depending on cooling - lubricant. Izv. Moscow Military District of the USSR, ser.: Mechanical Engineering Publ., No. 7, (1961).

[4] Wolf A.M. Metal cutting. 2-nd ed. L., Mechanical Engineering Publ. (Leningrad Branch), 1973, 496 p.

[5] Lubricating and cooling technological means and their application in cutting: Handbook L.V. Khudobin, A.P. Babichev, E.M. Bulyzhev et al. Under the general editorship of L.V. Khudobin.-M.: Mechanical Engineering Publ., 2006, 544 p.

[6] Latyshev V.N. Improving the efficiency of cutting fluid. M., Machine Building Publ., 1975, 88 p.

[7] Vasin S.A., Vereshchaka A.S., Kushner V.S. Cutting materials: Thermomechanical approach to the system of interconnections during cutting: Textbook for tech. universities. M.: Publishing house of MSTU named after N.E. Bauman, 2001, 448 p.

[8] Technological properties of new cutting fluids for cutting. Ed. by M.M. Klushin, M.: Mechanical engineering Publ., 1979, 194 p.

[9] A.N. Reznikov, L.A. Reznikov,Thermal processes in technological systems, M.: Mechanical Engineering, 1990. –288 p.

[10] A.A. Ryzhkin, K.G. Shuchev, M.M. Klimov, Processing of materials by cutting: a tutorial, Rostov-on-Don: Phoenix Publ, 2008, 411p.

[11] Yu.S. Dubrov and V.I. Garshin, D.Yu. Dubrov et al. Improving environmental safety in metalworking. Proceedings of the 5th International Scientific and Practical Conference Research, development and application of high technologies in industry,. St. Petersburg State Polytechnic University - SPb., 2008, pp.425-427.

[12] Klokke F. Dry processing of the base, boundaries, prospects. Message VDI 1240 On the way to dry processing - a technological challenge,. F. Klokke, K. Gershwiller, Dusseldorf: VDI Publishing House, 1996, pp.1-39.

[13] Installation of dry electrostatic cooling of the cutting zone during mechanical processing of metals STRIMEKO, [Electronic resource], Free access mode: http://www.ideasandmoney.ru/Ntrr/Details/136714, on 23.04.15.

[14] Khaustova O.Yu. Improving the performance of carbide tools and quality of machined surfaces during dry cutting of various construction materials: abstract of Ph.D. dis. of Cand. Of Tech. Sciences: 05.03.01. O. Yu. Khaustova. - M., 2004, 26 p.

[15] Canter N. The possibilities and limitations of DRY MASHINING. N. Canter. Tribology & Lubrication Technology, 2009, No. 3, pp.40-44.

[16] Dry Whirling Makes Economic Sense [Electronic resource], Free access mode: http://www.leistritzcorp.com/machine_tools_applications_dry_cutting.cfm on 23.04.15.

[17] Feng S.C. Cost and process information modelling for the dry machining. S.C. Feng,M.Hattori [Electronic resource], Free access mode: http://www.mel.nist.gov/msidlibrary/doc/cost_process.pdf, on 23.04.15.

[18] RF patent for useful model No. 194890 Cutter for fine turning with evaporative cooling, D.Yu. Dubrov, A.N. Chukarin, V.I. Garshin, V.L. Gaponov. Registered in the State Register of Utility Models of RF 22.10.2019 No. 2019133457.