Microstructural Analysis of Ti-6Al-4V Alloy after Plasma Immersion Ion Implantation (PIII)

Abstract:

The search for alloys with improved high-temperature specific strength and creep-resistance properties for aerospace applications has led in the last decades to sustained research activities to develop new alloys and/or improve existing ones. Titanium and its alloys are excellent for applications in structural components submitted to high temperatures owing to their high strength to weight ratio, good corrosion resistance and metallurgical stability. Its high creep resistance is of great importance in enhancing engine performance. However, the affinity by oxygen is one of main factors that limit its application as structural material at high temperatures. Materials with adequate behavior at high temperatures and aggressive environmental became a scientific requirement, technological and economically nowadays. The objective of this work is the mechanical and microstructural characterization of the Ti-6Al-4V alloy after treatment by nitrogen Plasma Immersion Ion Implantation (PIII) process. The aim of this process is the improvement of superficial mechanical properties of the Ti-6Al-4V alloy. The selected alloy after ionic implantation process by plasma immersion was submitted to creep tests at 600 °C, in constant load mode at 250 and 319 MPa. The techniques used in this work were optical microscopy and scanning electronic microscopy. The fractograph analysis of the samples tested in creep shows narrowing phenomena and microcavities. The creep results show the significant increase of material resistance, it can be used as protection of oxidation in high temperatures applications.

• Periodical: Materials Science Forum (Volumes 727-728)
• Pages: 50-55
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.727-728.50
• Online since: August 2012
• Authors: M. Castagnet, L.M. Yogi, M.M. Silva, Mario Ueda, A.A. Couto, D.A.P. Reis, C. Moura Neto
• Keywords: Creep Resistance, Plasma Immersion Ion Implantation, Ti-Al-4V Alloy

References

[1] T. Sakai, M. Ohashi and K. Chiba: Acta Metall Vol. 36 (1988), p.1781.

[2] M.A. Khan, R.L. Willians and D.F. Willians: Biomaterials Vol. 20 (1999), p.183.

[3] G. Welsch, A. Kahveci: I. In T. Grobstein and J. Doychak (eds. ), Oxidation of High- Temperature. Intermetallics TMS, Warrendale, PA, (1988), p.207.

[4] M.W. Kearns, J.E. Restall, Sixth World Conf. On titanium, Cannes, 1988, paper SU8, (1998), Les Editions de Physique, Les Ulis, p.396.

[5] M.M. Silva, M. Ueda, L. Pichon, H. Reuther and C.M. Lepienski: Nuclear Instruments and Methods in Physics Research. B, doi: 10. 1016/j. nimb. 2007. 01. 135. (2007).

[6] M. Ueda, M.M. Silva, C.M. P.C. Lepienski, J.A.N., Soares Jr. and H. Gonçalves H. Reuther: Surface and Coatings Technology Vol 201 (2007), p.4953.

DOI: 10.1016/j.surfcoat.2006.07.074

[7] C.B. Mello, M. Ueda, M.M. Silva, L. Pichon, C.M. Lepienski: Wear Vol. 267 (2009), p.867.

[8] American Society for Testing and Materials (ASTM). E139-83. Standard practice for conducting creep, creep-rupture and stress-rupture tests of metallic materials. Philadelphia, (1995).

DOI: 10.1520/e0139

[9] A. Sarkissian, V.A. Bourque, R. Paynter, R.G. St-Jacues and B.L. Stansfield: Surface and Coating Technology Vol. 98 (1998), p.1336.

[10] A. Loinaz, M. Rinner, F. Alonso, J.I. Oñate and W. Ensinger: Surface and coatings technology Vol. 103-104 (1998), p.262.

DOI: 10.1016/s0257-8972(98)00411-3